tent pole 3d models

Stand for 38 mm tent poles with holes for pegs

I adapted a smaller 16mm tent post to fit snugly onto a c-Clip, creating a sturdy support for a 22mm cross pole. I had printed the adaptor in PLA, carefully designing it not to clip too tightly around the pole, thus preventing excessive stress on the...

These are simple anchors that snap onto the poles of your grow tent for clamping small fans to. These snap fit onto 16mm poles. There are a few version, I was playing around with the shape optimization in Fusion 360. ...The one named clampvertallfinal...

Think I made for my neighbour's tent. ...The Tent Brand is DAC and there are 4 digits on the part 0489. ...Doubt it will be useful for someone.

Item is used on my 2010 Palamino 6149 pop up camper to secure the ridge poles to the interior frame of the slide outs.

Item is used on my 2010 Palamino 6149 pop up camper to secure the ridge poles to the interior frame of the slide outs.

I created extendable spreader bars to support bigger tents' roof structures. They clip onto 22 or 21mm main spars using two clamps at each end. Commercially purchased ones often fail the job, so I designed these alternatives to replace them. The...

I'm swapping out the clips on my rainfly setup. ...The tent poles come in at a diameter of 12.7 millimeters, or exactly half an inch. ...They're made from printed PETG plastic.

Customized version of http://www.thingiverse.com/thing:78398 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=78398 Instructions Using the following options: H2 = 2...

Customized version of https://www.thingiverse.com/thing:5260799 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5260799

Print with your preferred setting to suit the size poles. Probably better in PETG but I did use PLA for the ones I made. ...You will need to get some 8mm diameter mild steel rod cut to required length, then gets push fitted into cap.

Corner bracket for a grow tent that uses 5/8" poles. ...Lost two on our tent so made up some new ones.

Wyze Cam 16mm Tent Pole MountWith Metal Washer Magnet slot. Remake of type found elsewhere. Desiged for a 16mm pole maybe 5/8in as well. Print it and find out.What Basics I went with:Infill 10%Walls: 4PLA+The Wyze Cam v2 is compatible with the...

This will fit a 9mm fibreglass pole and could be used for dome tents too, or other things that use fibreglass or aluminium poles. Easily scale to suit your diameter pole within a couple of mm. This is printed in ABS with maximum perimeters for...

This will fit a 9mm fibreglass pole and could be used for dome tents too, or other things that use fibreglass or aluminium poles. Easily scale to suit your diameter pole within a couple of mm. This is printed in ABS with maximum perimeters for...

The poles sink in soft soil, which can change the pitch of the tent and cause you no end of issues in great weather, much less foul weather. And the metal tip is sure to wear out the fabric of the "pocket" where the trekking pole handle would...

i was looking for a telescopic pole for my awning project. most of those were unreasonably expensive so i decided to repurpose mope telescopic stick bought in a hardware store. top insert is intended to be used with m4 screws as a top 'spike'. ... ...

Customized version of https://www.thingiverse.com/thing:4597498 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4597498

Customized version of https://www.thingiverse.com/thing:4597498 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4597498

The 22mm clip from the original model did not work, so I wanted to upload this version. Print flat side down, no need for supports. I have also included a small clip that can be used as a stop if the weight of the fan/object is causing the mount...

The goal was to fasten the plastic part to the tent, then when stending up the tent the pole just need to push into that bottom part. It does not allow the bottom part of the tent to move up when using the zipper with one hand. The mushroom design is...

For 16mm or 19mm grow tent poles. ...Used for scrog or to reduce negative pressure wall deformation.

Designed to grasp and deliver paper towels in a camp kitchen setting, two units are necessary for the top and bottom of the holder, accommodating 22mm tent poles with ease. This versatile design can also be repurposed to hold other items. ...To ensure...

Replacement manual handle for the spring clips on a Eurmax standard tent pole.I printed in Prusament PETG, when one of the factory units failed. The replacement has lasted 2 years now!</p><p>It's important that the holes be precisely round, so the...

&nbsp;This was designed to print easily with no supports needed.&nbsp;Updated 9/12/2022: 19mm version tested and reported as good.&nbsp;Updated 9/1/2022: &nbsp;Added 19mm tent pole version by request. &nbsp;I have not tested it as I do not own a tent...

You can find the original here: https://www.printables.com/model/244929-16mm-or-19mm-tent-pole-to-22mm-pvc-holder-for-scroUpdated 6/14/24: Version 2: Much stronger than v1. Thicker walls with sharp 90 degree corners removed. Prints at 45 degrees so...

***Updated 11-7-2022 &nbsp;| Now Compatible With 15mm &amp; 22mm Tent Poles | ***Added 22mm ID versions of all clamps to add compatibility with grow tents that utilize 22mm OD support poles. If you need a version of these clamps with a different...

Receives 3/4" Poles Height: 3.75" (95.4mm) Width: 6.3" (160mm) Length: 2.7" (68.2mm) Recommend a very solid print as it takes a lot of pressure when the tent is assembled. Supports should be used during printing for the best results. ... Settings I...