tent pole clamp 3d models

... an M6*40-50mm hex screw, its accompanying nut, and 8mm shrink tube. By utilizing this attachment kit, tents or tarps with poles can be repurposed as the primary structure of tipi-style tents, eliminating the need for a cumbersome center-pole within.

Receives 3/4" Poles Height: 3.75" (95.4mm) Width: 6.3" (160mm) Length: 2.7" (68.2mm) Recommend a very solid print as it takes a lot of pressure when the tent is assembled. Supports should be used during printing for the best results. ... Settings I...

I'm swapping out the clips on my rainfly setup. ...The tent poles come in at a diameter of 12.7 millimeters, or exactly half an inch. ...They're made from printed PETG plastic.

<p>The pin in the default model is 4mm in diameter and the model "Flat" can be edited for whatewer purpose is needed.</p><p><br>The Thumb Nut hat 2 options - for thread tapping or for M3 Nut. ...For the M3 Nut the print must be paused on the 6.4mm mark...

The pin in the default model is 4mm in diameter and the model "Flat" can be edited for whatewer purpose is needed. The Thumb Nut hat 2 options - for thread tapping or for M3 Nut. For the M3 Nut the print must be paused on the 6.4mm mark and the M3...

The goal was to fasten the plastic part to the tent, then when stending up the tent the pole just need to push into that bottom part. It does not allow the bottom part of the tent to move up when using the zipper with one hand. The mushroom design is...

.4mm nozzle, 25% infill, with 4 walls to ensure no infill is placed inside the thin wall of the clamp mechanism.Bolts used from this kit: https://www.amazon.com/gp/product/B07HQ5761L/F3D file included for modification. ...Permission is not given to sell...

Wyze Cam 16mm Tent Pole MountWith Metal Washer Magnet slot. Remake of type found elsewhere. Desiged for a 16mm pole maybe 5/8in as well. Print it and find out.What Basics I went with:Infill 10%Walls: 4PLA+The Wyze Cam v2 is compatible with the...

i was looking for a telescopic pole for my awning project. most of those were unreasonably expensive so i decided to repurpose mope telescopic stick bought in a hardware store. top insert is intended to be used with m4 screws as a top 'spike'. ... ...

I designed a versatile clamp and clip attachment specifically for camping poles, intended as a backup solution in case of adapter loss or when adapting poles for alternative uses.

Can be printed without support. ...Uses a 6x25 fastener for the pole clamp and reuses the hardware from the fan for the other side.

This DIY project involves integrating a GPS mount into a 36mm pipe clamp, providing a versatile solution that can be easily adapted to fit different diameter poles. The design caters specifically to scientific fieldwork where the simultaneous use of...

This cable clamp is specifically designed for use on poles measuring 1.375 inches in diameter, so be sure to take note of that crucial dimension. It will not fit standard t-bars, which are typically only 1.125 inches wide. ...This particular clamp is...

ANTENNA CLAMP

tent

I got two geocache concepts mixed up. ...The pole part is actually a clamp for 60-61 cm road signs with a 70mm tall screw-on container. ...There's plenty of room to fit a rolled-up log, pencil, and even a small trackable item inside.

This clamp secures firmly onto the vertical pole of a dog agility jump, holding the horizontal pole in place. A deliberate design choice makes the supporting part extremely shallow, ensuring it falls easily if the dog bumps into it, preventing...

I saw the clamp by rainb0w_wheez3 at https://www.printables.com/model/20305-intel-nuc-pole-mount whic had the perfect mount for my Arlec LED floodlight that I wanted to attach to my camera pole.  problem is it fits a 35mm pole and mine is 15mm.  it...

While the nubs are strong enough to hold the weight of the basket plus another 30-40 ibs (depending on your print settings and material), there are four holes drilled into the corners so you can slide a screw and nut into the clamps to help ease the...

Use a coin to tighten it.Put the three main pieces together as shown in the pictures.Use the longer bolt to secure the pieces to each other and clamp them to the pole.Insert the second nut in to the space for it that is in area where branches are...

Clamp for round tent BeastWay pool 366x122 cm

Sony PX470 Voice Recorder Case and Pole Mound for Insta360 poles 24mm and 31mm 24mm is for the standard insta360 invisible stick. ... 31mm is for the insta360 invisible tripod stick.

I crafted a device that joins two trekking poles side by side, forming a stable tripod for uneven terrain. ...This innovative system secures the poles at a precise 60-degree incline and incorporates a custom-designed rifle rest atop the assembly.

To achieve this, create a simple clamp that can be printed using elastic filaments like ASA or ABS. This will provide the necessary flexibility and durability for the clamp. When adding or removing the clamp, exercise caution to avoid damaging the...

Sony PX470 Voice Recorder Case and Pole Mound for Insta360 poles 24mm and 31mm 24mm is for the standard insta360 invisible stick. 31mm is for the insta360 invisible tripod stick. Print Settings Printer Brand: Creality Printer: CR-10 Rafts: No...

Simple clamp to fix the tarpaulin on INTEX pools.This should avoid the tarpaulin to be blown away on windy days.I recommend to print this with somehow elastic filaments like ASA or ABS.To keep the camp flexible i also recommend to print it without...

Customizing options include gopro_secondary_rotated = 0, gopro_bar_screw_head_d = 6.2, gopro_secondary_what = clamp, gopro_bar_screw_shoulder_th = 4.5, gopro_bar_screw_nut_d = 6.01, gopro_captive_rod_angle = 45, gopro_bar_screw_d = 3, gopro_bar_gap =...

Customized version of http://www.thingiverse.com/thing:78398 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=78398 Instructions Using the following options: H2 = 2...

Customized version of https://www.thingiverse.com/thing:5260799 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5260799