tent pole clamp 3d models

daher hier die Maße des flachen Stücks : Breit: 34 Dicke: 3 Loch Durchmesser: 8 English: I needed a better adaptor for my Tent Poles the Original universal adaptor dosent fits my needs. So i hope you can use this also. ...I didnt know if this flat pole...

This is a 7cm extension suitable for use with the original tent poles of various Babboe Cargo bikes (City, Big, Dog, Curve, etc.).These extensions enable the use of tailor-made covers that provide additional space and headroom.I've designed the upper...

Think I made for my neighbour's tent. ...The Tent Brand is DAC and there are 4 digits on the part 0489. ...Doubt it will be useful for someone.

Item is used on my 2010 Palamino 6149 pop up camper to secure the ridge poles to the interior frame of the slide outs.

Item is used on my 2010 Palamino 6149 pop up camper to secure the ridge poles to the interior frame of the slide outs.

This is a double-sided clamp for a monitor pole (33mm diameter pole). Its not pretty, I'm not a designer by trade but it works to add a pole extension to your existing monitor pole for a light monitor. (I would NOT use a full sized monitor with this...

I designed this simple clamp that attaches to a 24mm diameter pole with a single screw and nut. The screw goes through one side of the clamp, then through the eyelet of the flag, then through the other side of the clamp and tightened with a nut. ... ...

 The length allows for still assembling and disassembling the tent pole, and can be slid to lock the pole together for easy pop-up without the pole pieces falling apart.Printing is really easy - I used the Ninjaflex profile and printed in black...

... I used 80% infill for strength. I tried this print with black PLA and you can tighten the pole quite hard. Stress tested one that broke in the middle after really tightening it too hard. ...Will also try this print in ABS and see if it is stronger.

A clamp for attaching equipment to a round pole or pipe (or maybe for attaching a pipe to a wall). ...Pole size, clamp dimensions, and hole sizes are all customizable.

A clamp for attaching equipment to a round pole or pipe (or maybe for attaching a pipe to a wall). ...Pole size, clamp dimensions, and hole sizes are all customizable in OpenSCAD.

A clamp for attaching equipment to a round pole or pipe (or maybe for attaching a pipe to a wall). ...Pole size, clamp dimensions, and hole sizes are all customizable in OpenSCAD.

Extra small (3,5x1,5cm) tent tarp clamp to tension a window cover with two tent poles. (Aluminum poles 8.5mm diameter) -------------------------------------------------------------------------------------- Extra kleine (3,5x1,5cm) Zeltplanen Klammer...

This two parts should be used on quick connection clamp to connect two poles together, one parallel to the other or perpendicular. ... I will post a picture ASAP.

I've build a clamp to hold my weather sensor shield at an antenna pole (43mm). This time I used wood screws / Spax to tight the clamp together. ...I'm not really satisfied with that try, but you can use countersunk head screws, that's better.</p>

I've build a clamp to hold my weather sensor shield at an antenna pole (43mm). This time I used wood screws / Spax to tight the clamp together. ...I'm not really satisfied with that try, but you can use countersunk head screws, that's better.

... for little birds. ...This clamp can be attached to such a pole (if too loose, add some paper or plastic sheets for tighter clamp). It provides a stable foundation for large plastic boxes (e.g. ...for cakes or veges) and stops squirrels climbing up.

The clamp is designed specifically for a stock pole, utilizing M4 bolts for secure fastening. A visible PNW CREW logo is the sole notable feature on this particular model. ...However, I didn't create this design, as it was provided to me some time ago.

Designed to clamp onto the lowest section of the pole stand. Feed the cable through the bottom and connect, the power supply should fit snug with the feet going into the cutouts. Tilt the power supply away from the pole to remove. ADDITIONAL HARDWARE...

I wanted to design something to hold a pole right near my picnic table and found [falconphysics' V-Groove Table Clamp](https://www.thingiverse.com/thing:2399418) to be the closed to what I had in mind. Remixed it a bit to suit my need: - Chopped...

I designed this 'Power Pole Pair Clamp' to replace the pin. It is printed with the center pin flat on the bed, which makes the pin stronger. The pin is also flattened on the bed side to increase strength and beveled on the end to ease insertion. ... ...

This is a simple clamp suitable to ATL LTE in order to asjust pan and tilt

... Options Available for Use: nut_type = 12 (set default value is Socket Head Cap) clamp_height = Sixty (minimum ten, maximum three hundred forty, in increments of two point five millimeters) screw_hole_diam = Nine point five six (minumum 2mm, max.

The poles sink in soft soil, which can change the pitch of the tent and cause you no end of issues in great weather, much less foul weather. And the metal tip is sure to wear out the fabric of the "pocket" where the trekking pole handle would...

I'd be happy to assist you! However, I need a text to spin. ...Please provide one.

Curtain Coat Hook, sturdy 23 millimeter rod

This is a high-end canopy top for bigger rods featuring a sturdy apex.

Modeled specifically for Reddit user Fuk_Kek, this text aims to capture their attention and spark interest in the topic at hand. ...With a focus on providing relevant and engaging content, it showcases the writer's ability to tailor their work to suit...