technics sl 1200 dust cover hinges 3d models

Tried to modify https://www.thingiverse.com/thing:2774791 to fit my Technics SL-D303. The post on this remix is shorter and skinnier than the original thing. I had some trouble getting the right fit and ended up trimming some off the end after...

It allows you to tighten the hinge and keep it in place, while allowing the arm and attached dust cover to open and close freely. You then use the set screw to tighten the hinge much more easily. ... After months of frustration and adjustment with the...

I had to replace my SL-BD22 rubber feet gone for age, they totally melted. So I had a new TPU spool and a I gave it a try. ... It works :D

A user-requested SketchUp design for a turntable model is available, accompanied by a sketchup file. ...To assemble it, utilize a sized bit to drill arm and feet holes, then secure with glue.

A custom turntable model created specifically at the user's request. The design was crafted using SketchUp, a powerful 3D modeling tool. ...To facilitate further exploration and manipulation, a SketchUp file has been included with this submission.

I'm restoring a Technics SL-1300 that had a nasty mark on its paint where a record cleaning arm had been superglued onto the deck, so I designed this 45 rpm adapter holder to cover the mark while hopefully complementing the design of the record...

COMPATIBLE HINGES FOR TECHNICS TURNTABLES SL-J110R / SL-J100R / SL-J90 Info: Designed these print in place hinges from scratch, as the hinges from @wezner aren't too realiable and you can easily break them while mounting. Signed this as a remix as...

Carefully cut through the thinnest portion of the plastic part at the very top to release the retaining pin.

This is a replacement Rca Clamp & Spacer for the Technics 1200/1210 -Modeled on the original part with a few tweaks to increase strength with the minimal space available. -The added Technics Logo helps to increase rigidity of the design. ...-The STL...

This is a replacement **Rca Clamp & Spacer** for the **Technics 1200/1210** -Modeled on the original part with a few tweaks to increase strength with the minimal space available. -The added Technics Logo helps to increase rigidity of the design.

A remix of the excellent Technics 1200 turntable by FatalDischarge. https://www.youtube.com/watch?v=QBF-LFDstS4 Modified by adding a base, and a hole through the turntable. You can then print a small record to place on the turntable. I did this on...

A clever mashup of the iconic Technics 1200 turntable by FatalDischarge. Check out this remix on YouTube: https://www.youtube.com/watch?v=QBF-LFDstS4. This creator took the classic design and added a sturdy base, along with a hole through the...

An 45rp Adapter for Technics sl-j110r replace part

Only one solution seems viable: the Technics 1210. Hehe, I know the tonearm is missing – it was a deliberate design choice for ergonomic reasons. Feel free to print these designs! They're inspired by my love of gin and vinyl. ... If you want to...

... be able to mount the new element in place with the original screw. Works on many technics SL-xxxx record players. Tested and working on a Technics SL-1900. ...Replaced the original National Panasonic 270 C-II with a AT-VM95E witout any problems.

Rigg options can be viewed in a video for better understanding - https://www.youtube.com/watch?v=5O_mqSh9IS4 Operation Buttons and Knobs: Power: toggle on/off Playback: start/stop RPM: select 33 or 45 Pitch: adjust by +8% or -8% Lamp: turn off/on...

Custom Turntable Component for Technics SL-DL1. The part uses a standard spring with 27 mm diameter and a short piece of silicone hose, 15.5 mm in diameter. A layer of felt is also added underneath. You can modify the dimensions using the provided...

This is a replacement for the worn-out gear of your Technics turntable SL-B3.\nOriginal Part Number: SFTJ202-01E Shaft Turntable\nCustomized version based on http://www.thingiverse.com/thing:1516585\nCreated with Customizer!

A replacement component for the SL-J2 Technics record player is needed. Rather than a solid platter, the design includes a plastic donut for playing 45s with a hole in it and a spring-loaded puck that locks in and out, ensuring you never misplace...

It includes two cartridges (Shure M44C, Ortofon Concorde PRO S), four slipmats, a vinyl record, inside chips, dust cover, AC & RCA cords, and is perfect for close-up shots. The rig offers various operation buttons/knobs, tonearm options, detailed...

In the 1980s, Technics, a Japanese firm, crafted an exceptional device.

I tried to model this to the original Technics feet as closely as possible. May raise the turntable slightly higher.  Printed with solid infill in TPU, cup down with support on build plate only. You can reuse the original washer and nut but will need...

This is a replacement back rivet for the Technics Linear trackers listed in the title. It could work for a couple other Technics linear trackers, but I do not have them to check. The original rivets have a tendency to break if you are not careful in...

You'll need to do some DIY work on this bracket. First, cut the old brackets flat using a Dremel to remove most of the bulk and then file the rest down for a smooth finish. Next, apply some polish to clean up the cut edges. Once you've done that,...

print without support 20deg turn on the side

Revamped the .SKP for accurate slicing and added an .STL from that .SKP; repaired using Netfabb. However, it must be scaled down to 0.4 times its size due to fitting issues. ...Printed with a Solidoodle 2 at .2 mm layers, 3 shells, and .2 infill.

I designed this to replace a broken dust cover hinge on someones turntable.

Vinyl enthusiasts rejoice with our premium dust cover hinges designed specifically for your cherished LP turntables. Durable and long-lasting, these hinges provide a secure and stable closure mechanism, safeguarding your records from dust and other...

Designed a cover for Epos Sennheiser GSX1000/1200 External USB Soundcard. The design is for GSX1000 but it should fit GSX1200 without problem. ... Printing:

User Interface: Play Area Dust Shield Hinge Utilize a 2.5 millimeter by 18 millimeter pin or bolt nut.