team associated rc10 models

This is a rear body post adapter allowing you to run a team associated Reflex 14T Truggy body on your 1:16 mini revo. On the lowest post setting this adapter and and body combo still clears the hot racing sway bar kit (front and rear) with the...

This is a flat bar (paint stick) wheelie bar for a Team Associated B6.x No Prep Drag Car (NPRC). The body and part 2 are templates for cutting out of a 3mm thick sheet of carbon fiber. The pad is 100% infill PETG. Misc M3 screws (button and flat...

This is a rear body post adapter allowing you to run a team associated Reflex 14T Truggy body on your 1:16 mini revo. On the lowest post setting this adapter and and body combo still clears the hot racing sway bar kit (front and rear) with the pivot...

Dwarf Mortar Team (2 Models) This set includes:- Dwarf Artillerist- Dwarf Watchman- 1x Base (25mm)   All of them unSupported and Pre-Supported (You can also find this model in our January 2024 Monthly Release, in the Monthly Releases Collection)  ...

I designed this because the nylon pistons from Team Associated was too expensive ($AUD 22 for 4). The dimensions are: 12.8mm diametre 2.4mm total piston thickness 2mm piston disk thickness 2.4mm centre hole Update 20230313: Added new file...

... to fit inside the body. I am currently using a Jconcepts F2, but it's uncertain whether other models will be compatible. ...The layback transmission requires this spacer, whereas the laydown has sufficient room for a fan to fit without any issues.

Reverse engineering a new car, and this is my progress so far.

Rear lower shock mount for the RC10T2. The holes for mounting the arm could be reamed larger to allow the screws to pass through more cleanly (if desired). ...The shock mounting holes should be tapped with a 4-40 tap.

Car owners can modify the roll center by adding gear box spacers, which come in 0.5mm, 1mm, and 1.5mm thicknesses.

I needed adapters to mount my B6 gearbox on my SC6.1 chassis for a no prep car, so I built the stack to be 8mm and the spacers to match. I replaced the rear gearbox brace with a taller part, and added a wheelie bar mount. Then I got greedy and did a...

I needed to bring my mounts forward for my bump box YouTube Channel https://www.youtube.com/channel/UCZ8WG-kqF1kmL2s0xIMfIIg If you found this video helpful or would like help fund future experiments.please donate below. ... Patreon ...

This is a LiPo battery front stop to keep your battery from rear-ending your electronics. It will bolt on to the antenna/shock mount, see in the picture. Use a M3x4mm BHCS screw sth. ...in that range.

If you're installing a receiver on the opposite side of the motor and you've taken off those protective guards, this is the bracket you need to mount your antenna. ...To get the best outcome, print with PLA at an infill of at least 50%.

Front body mount bracket for the RC10T2. ... You may need to ream out the screw holes slightly, but 4-40 screws should thread in just fine.

Front mini bumper for the RC10T/RC10T2. This is designed similar to an OEM aftermarket bumper (RPM) that was available once upon a time. They are getting incredibly difficult to find on the web, and there are probably more durable options...

Front body post mounting bracket for the RC10T2. ... This is not a very complex component, but print orientation will be critical to maintain strength.

I made this for my tc6 because the factory ones kept breaking

A custom battery bracket was constructed after the replacement battery's dimensions had grown wider.

You'll find a collection of useful parts for your AE B6.1 here. Note: STL references may print but often do not fit exactly. However, printable components have been printed and verified to be exact fits. Reference photos can be used in Fusion 360...

Avoids purchasing an entire transmission case just to replace one minor component.

Servo mounts for the RC10T2 and spacers for setting servo position. These are designed for a 0.2 layer height, so they are not an exact match for originals (2.4 vs 2.5 mm). These could easily be modified to match. ... Tap the mounting holes with...

More squish = More tractionIf you have the TR28 wheels, you can use the Nanosport street tires since they are the same size.Make sure to chase with a 2mm drill bit.

Extended body mounting posts for custom Rally bodies.

The standard button head screws on the shock tower can cause the body to crack prematurely. Putting this little body mount on the shock tower helps prevent this. It's very strong and fits very nicely. You will need to replace the standard BHCS-M3x12...

The new B7 battery mount system is pretty good actually but with my low profile batteries there was quite a bit of vertical play, obviously I could put some foam etc but decided I'd try to create an oring mount.You'll need a 61mm (inside diameter)...

My original ones broke and I didn't want to pay the huge prices for "vintage" parts. I race my T4.2 on a track made of Astroturf over concrete with very big jumps, so it is very rough on the car. ...I have only broken 1 printed bottom cap over the...

A rear shock tower designed for the SC10 R/C car. ... This was a student project that we machined for his car.

I needed adapters to mount my B6 gearbox on my SC6.1 chassis for a no prep car, so I built the stack to be 8mm and the spacers to match. I replaced the rear gearbox brace with a taller part, and added a wheelie bar mount. Then I got greedy and did a...

Cablemount to fix the lose cables in front from the middle diff 4mm cables

Side battery mount for the AE B6 series