teaching tech bl touch 3d models

Creativity Unleashed: CoreXY ELF 3D Printer Takes Auto-Leveling to New Heights with BL-touch and 3D-touch Mounting Brackets. Upgrade Your Printing Experience: Unlock the Full Potential of the CoreXY ELF 3D Printer with Advanced Auto-Leveling...

... probe at a position where it will not hit a Pi cam mount placed on the QR Code covering the X axis motor.This was only tested with a CR Touch. ...I'm assuming the BL Touch has the same dimensions has not to hit the Pi cam mount when homing the X axis.

 Also needed a mount for the CR-Touch/BL-Touch. ...Had one for the stock setup and worked great, but this fan mount interfered with it since it used the same mounting holes.Mixed in my CR-Touch mount with Lautrec_996's 45 degree fan mount.Let me know if...

Also, the runout sensor seemed a bit too low and would make contact with part of the sprite.I added the cutout for the connector.I extended the CR Touch's mounting point out a couple of mm to avoid the sprite's bolts.I extended the runout sensor's...

This modifiable module is designed for the Alfawise U20 ( compatible with Alfawise U30, Creality Cr10, Tevo tornado and other printers with a similar mounting system ).\r\n\r\nThe Fang can accommodate various hotends including MK8/MK10 heads, E3D V6,...

Designed to attach to the CR Touch / BL Touch attachment plate for a Creality Ender 3 v2, such that both can be used on the printer at the same time. Part is strongest when printed with the tube upright, but other than that it can be printed...

Compact Reality Ender 3 Extruder Protection (Cover) with Provided Standard Cooling Locations and Mount for BL Touch (3D Touch). A model without a sensor mount is also included. Advantages: Compactness Properly Formed Cooling Flows, Easy Maintenance,...

BL Touch\3D Touch mount for Flying Bear Reborn e3d v5/6 volcano This mount is suitable only for Flying Bear Reborn with modified printing head: - Extended version of BeMeGe-extruder (https://www.thingiverse.com/thing:5198016). Also it should suit for...

I crafted this solution because I couldn't locate a suitable 40mm fan mount that accommodated 3D touch and my hotend's unique protrusion. This design will support any thickness of 40mm fan, BLtouch, and the E3D silicone sock effortlessly. UPDATE:...

Everything can be printed without supports except the reverse mount (just put the brackets vertically) Works with - 40 mm fans, - 2 in 1 fan duct (https://www.thingiverse.com/thing:1710217) - standard CR-Touch bracket - ??? I made it recently, so...

Protects the delicate probing pin from snagging, dragging, or contamination, extending the overall lifetime and accuracy of your touch probe. When the probe retracts, it retracts safely within the shield. When it extends, it extends just far enough...

ABL mount for Kingroon.

A straightforward fix for integrating the 3DTouch feature into your Anet A2 Plus printer involves connecting it directly to the machine's interface board. This can be achieved by attaching the sensor wires to specific points on the board, as...

Remixed from Mesmer88 - a commenter said to make it thicker so I did.You may be able to get away with stock M3 screws by putting the bracket over top of the fan mounting shroud. Better is to get slightly longer M3 screws and place the bracket under...

Auto bed leveling mount for the x301 or x201 printer.

I had a hard time finding a cr touch mount for the bondtech ddx that was higher than the print nozzel, i modified this to have the proper offset and it fits perfect with the microswiss hotend

Voron Switchwire x-carriage w/ heat set holes for an external mounted BLtouch.BLtouch is to sit to the left; added a regular right carriage to keep it even.test fit looked good, but fried my BLtouch before function testing. Got the measurements from...

There is some one design the mount but it seem, i cannot adjust the height or routing the wiring properly, thus i have created this to mount on my Printer

I liked the hex light ports on the original but the BLTouch has a very bright Red light that is a bit annoying. Especially on a web cam. ...So I plugged the front holes and left the sides open.

I liked the hex light ports on the original but the BLTouch has a very bright Red light that is a bit annoying. Especially on a web cam. ...So I plugged the front holes and left the sides open.

I opted for a 400mm square bed, but it proved too massive to tackle leveling and maintaining a stable orientation. ...As a result, I designed a custom mount that snugly fits into the two threaded holes located on the left side of the fan shroud.

this shouls work with m3 screws with no nuts

I'm looking for a convenient and easy-to-use tool to level my 3D printer's MK8 extruder. ...A well-designed auto-leveling accessory would be perfect for the job, making it simple to achieve precise and consistent results with minimal effort required...

Auto leveling arm for the ToAuto Pyramid A1.1 printer. The original one was too flexible so I made this one. ...This one is geometrically stronger and can be easily printed.

Voici un support pour améliorer l'estetique du câblage .

I added two new models, one with a thickness of 2 mm and the other with 2.5 mm. ...The 2.5 mm model turned out to be quite sturdy.

A feature that automatically adjusts the printer bed height in RepRap 3D printers is called Sensor AutoLeveling.

To simplify screw installation, the mounting screws were redesigned to offer a snugger fit. ...This tweak also clears more space for the connector to securely connect between the BLTouch and its bracket.

<p>This is a remix from <a href="https://www.thingiverse.com/thing:4751635">thingiverse.com/thing:4751635</a> by travelcamel!</p><p>- Added holes to secure the cover via the 2 screws<br>- Added a mirrored version to mount it on the right side</p>

These are the parts I designed to convert my Makergear M2 printer to the e3d hotend and added a BLTouch sensor to auto level my scewed printbed. ... The part for mounting the cooling fans, I printed with my ANYCUBIC Photon Mono resin printer, the rest...