teaching tech bl touch 3d models

This design brings the BL touch very close to the nozzle and accommodates two 40mm fans for good cooling. I run the hot end cooler blowing outward "away" from the printed parts. The design is meant to have 3mm brass melt-in inserts where...

This shield provides protection.It also makes it much easier to transfer the BL Touch between extruders because it replaces the two 2mm thick washers under the BL Touch which are a pain to line up.Print with a high temp filament such as eSun's...

Compact BL-Touch integration in the design by @evil_k Screws for BL-Touch are M3x8 and they do not screw into the mount. They are only used as a guide so that the springs are not falling out. For mounting you need 1x M3x10 (top right) and 1x M3x12...

BL Touch GEETECH : Learn more : https://www.amazon.fr/dp/B08SBPNK3Z/ref=cm_sw_em_r_mt_dp_ZZXAG4WFTG6ZP5QFTYMY?_encoding=UTF8&psc=1 BONTECH direct drive print head : https://www.bondtech.se/product/bondtech-ddx-for-creality-ender-cr-10s/ Attention...

Remixed to offset the BL touch so that it doesn't interfere with the stop switch and is at the right height not requiring shims. Added a means to secure the bottom left screw (can cover hole with tape after secure). Added wire clearances for BL...

Исправлен размер паза второй турбинки с 39 на 40.2 ммChanged second fan slot from 39 to 40.2 mmUPD 11/04/2024Добавил пока не тестированную модификацию для BL-TouchУстановил — требуются небольшие правки по толщине платины для bl-touch, но пока можно...

Santana for ender 5 plus, steel bl touch for 4020 blower fan. ...Made in tinker cad because fusion 360 wasn't working for me, so you may have to clean up some of the edges.

This is a Remix of Satsana Ender 3 Fan Duct https://www.thingiverse.com/thing:4369859 Offset: X: -47 Y: -8 Direct drive mount - https://www.thingiverse.com/thing:3386628 Bl touch spacer - https://www.thingiverse.com/thing:3072487

Custom support for the direct drive extruder BIQU H2 compatible with Creality Ender 3 serie and Creality CR10. ...You can install BL touch. ...You need printing support just for the Cover.

I printed this E3d v6 mount https://www.thingiverse.com/thing:3181800 and needed to add a bl touch to it. ...I haven't printed yet, but will update pictures when i can.

Bl-touch support for ADKS - ENDER 3 FAN DUCT V3 https://cults3d.com/en/3d-model/tool/ender-3-adks-fan-duct-no-supports-needed offset : x:-43.2 y:-6.0

Added a BL touch bracket to the mount for the Ender 3 v2 Pet fang Fan duct. ... UPDATE: Edited the bracket so the pin will be lower then the nozzle.

I bought a laser engraver from creality-shop. ...It is attached to the original fan with magnets. Due to my modification and the BL-Touch this was not possible. ...I have a holder with magnet designed.

I bought a laser engraver from creality-shop. ...It is attached to the original fan with magnets. Due to my modification and the BL-Touch this was not possible. ...I have a holder with magnet designed.

This adapter accommodates the nozzle beyond the print boundary, allowing for straightforward calibration of your BL-Touch Z axis without encountering endstops... ... *** Note - This method won't be compatible with newer models featuring expanded build...

This is a Remix of Satsana Ender 3 Fan Duct https://www.thingiverse.com/thing:4369859 Offset: X: -47 Y: -8 Direct drive mount - https://www.thingiverse.com/thing:3386628 Bl touch spacer - https://www.thingiverse.com/thing:3072487

A remix of the https://www.thingiverse.com/thing:2823129 that adds a BL Touch Mount on the right side of case. ... You need to configure the XY Probe position in your firmeware or using the M851 GCode.

Custom support for the direct drive extruder BIQU H2 compatible with Creality Ender 3 serie and Creality CR10. ...You can install BL touch. ...You need printing support just for the Cover.

Angepasster Fan Duct für den BL-Touch Mount https://www.thingiverse.com/thing:4714981 Print Settings Printer Brand: Velleman Printer: K8800Rafts: No Supports: YesResolution: 0.1 Infill: 25% Filament: OWL PLA Orange Category: 3D Printer Parts

Ender 3 BL Touch simplified and close to nozzle#define NOZZLE_TO_PROBE_OFFSET { -27, -9, -1.68 } https://www.printables.com/model/331865-ender-3-pro-fan-shroud

Bl/3D Touch remix, right side mount with adjustable screws. Requires 3 M3 screws and nuts. ...May need to heat the nut up with a soldering iron to get them into place as its a tight fit.

this is a remix of the BL Touch bracket for the BMG direct drive mod for a cr10s. This remix slightly adjusts the position of the probe and permits access to the probe grub screw to adjust the pin or replace it without removing the probe from the...

Created some space on the side duct mount to allow the installation of the bl touch mount that came with my bl touch (similar to this mount but in metal : https://www.thingiverse.com/thing:3978365 ) Much more solid then using the mount i designed...

The BL-Touch bracket that came with the Fang collection from ozfunghi didn't quite fit the thicker ~2.6mm hotend carriage on my Ender 3. I made a quick adjustment in Tinkercad to make it fit properly. It still sits high, and does not work with the V3...

I've had fantastic results with the original components of this extruder, but I really needed a BL Touch mount option and wanted to upgrade the part cooling fan to surround the nozzle more effectively. So, I snatched the fan nozzle from the new...

Use this Remix to attach your BL Touch onto your Ender 3 V2 if you use either the - "Ender 3 Silent Fang Noctua V2" attachment", by Aharriau, - or the "Pet Fang mount for Ender 3 V2 use all three mounting holes", by Michealfordltd2 this remix is...

Super simple BL-Touch mount for use with 4020 fan on the BMG V6/Dragon Directdrive mount by nean_ Link to the mount: https://www.thingiverse.com/thing:4336908 Probe offsets: X -23 Y -33.5 Update: Made the top part thinner because the BL-Touch needle...

Havent tested it yet I fittet 2 M3x6 threaded inserts from the top secure the BL-Touch What you need 3x M3x6 screw 2x M3x6 threaded insert Edit* I also added a new X-Axis endstop because mine didnt work anymore. Fits the original endstop. Endstop...

The BL-Touch does not cover airflow and is positioned 31mm to the left and 15mm in front of the nozzle on my E10. It works flawlessly with Marlin 2.0.4.4. You might need two M3 nuts and two M3 screws... ...I based this modification off of thing #2481362...

... are required. (you need two screws for the BL-touch, if they were not in the package.) Just unscrew the two screws holding the housing of the printer head and use them later to screw the device and the housing to the printer head. ... enjoy