tbs source one v4 3d models

I Designed this little RX Holder for my TBS Source one to fit over 2 posts to mount my ELRS receiver in the front of the drone.

Antenna holder for TBS Source One. ... Accommodates BN880 GPS+Compass module, (RP-)SMA connector with or without flange and two whip antenna tubes for diversity receiver like FrSky R-XSR.

The vehicle is equipped with a TBS Source One camera system, featuring an Immortal T vertical setup with a vtx transmitter and a GPS rear mount for precise navigation and aerial photography capabilities.

## TBS Source One V3 Air Unit + Immortal-T mount Remixed to remove the GPS holder and remove the Rx tray above the Air Unit to make the space more versatile.

Designed to fit the TBS sma adapter and a CF immortal T antenna, fitting into the new source one v5. ... Pint upright with supports in TPU, will need a cut to allow you to install the antenna.

This antenna tail for the TBS Source One v3 is the perfect solution to mounting your vtx sma antenna and your diversity receiver antennas, but with still the space to get your XT60 wires out of the back!

Remixed Immortal T mount by grou69 adopted to TBS Source One Frame with locking mechanism that secure the mount from rotating on standoff. ...It's made for V2 Immortal T antenna.

TBS Source One V5 Micro AXii 2 antenna mount. ...This version is for the VTX antenna only and does NOT have a provision for an ELRS antenna https://youtu.be/Y0Gkqp5ILKs

Camera Mount for TBS Source One v0.2: Utilizing Session5 and Runcam 3S. ... Following numerous designs, I discovered a configuration that perfectly meets my requirements and offers maximum versatility: Version 5.

Gopro tilt stop mount for tbs source one V5. min. tilt is about 5°. Print in TPU with 60% infill for best fleibility and stability. ... Hope you like it!

Just a simple alternative air unit antenna mount for TBS Source One that works with https://www.thingiverse.com/thing:3877592?fbclid=IwAR0WquM0WI8mMaDJWUkRSttjPinSNZArIMsPnidAPc1yiqMCb66mNodaUxY You can see implementation here...

* 30° GoPro Hero 9 Mount for the TBS Source One v0.1.1, remixed from FR mount by stynkebutt and adapted to mount to the source one frame. * As with the original, the print does not require supports. * Recommend printing in TPU. Note: In the...

... and keeps the mount firmly in place. Supporting the open source project, brought into existence by Team Black Sheep, is easy and straightforward. Simply visit their GitHub page at https://github.com/tbs-trappy/source_one for all the details.

This is meant to hold TBS M8.2 GPS unit on the back of a TBS Source one frame. I have not tilted the unit because it would interfere with my bnc antenna, but you can still use a heat gun in order to angle it once in position if you need. The GPS I...

Made a GoPro Hero (9,10,11) Mount for the TBS Source One V5. ... 25* degree up tilt I uploaded two versions, one with no text, and the other with my handle/nickname (VANISH) on it if you want to rock it :)

I made a mount for GPS, Crossfire and SMA all in one for a TBS Source One V5.I am printing it with TPU and 40% Infill. ...That'll do i guess</p><p>Feel free to tip me : paypal.me/richi241</p>

I designed a TBS Source one's mount for the CADDX Ratel 2 Micro.This mount using the original carbon camera support It's attached to this one with two M2x10 screws. Two pins are catch in the carbon support to lock the camera at 0,10,20,30 or 40°.

Couldn't find an antenna mount for the O3 antenna on the TBS Source One V5, so I made my own. Notes: Have just finished it, have not tested it. I will update this as soon as I get it printed and tested, but all measurements add up. Do mind this...

This is a camera mount for the TBS oblivion camera with the TBS source one V3, so the conception come with a full sise camera 27 x 27 mm and a 18 mm lens. the angle of the camera can be up to 0 - 60 degres angles. some modifications can occur. ... ...

I swapped out my Wizard x220 for the TBS Source One v3, and it quickly became apparent that the standoffs were spaced differently. To adapt my design, I modified it to match the Source One's mount, which necessitated a remix. ...The printed part is made...

Camera Mount on Standoffs for Caddx Nebula Pro Nano (TBS Source One v5)It fits very well in between the Cam-Holder with 14mm wideIt comes in 6 AngleLike circa 13 / 16 / 19 / 22 / 25 / 28 degreeGood for beginner to start with lower angle

VTX and RX Diversity Antenna Mount for TBS Source One. It's functional, though not exactly aesthetically pleasing. This makeshift solution is actually a hasty mashup of various designs but it gets the job done. ...It can accommodate VTX SMA connectors...

I'm attaching the antenna dock for the TBS Source One, which can be secured using just two small zip ties and some heat-shrink tubing to stabilize the RX antennas. ... Upgrade V2 involves enlarging the hole to accommodate the AXII with its 90-degree...

remix of the TBS Source One V5 Vifly finder 2 buzzer. shoddy remix of the original, not very clean but does the job. the only thing different is that the buzzer sits further back in between the stand offs. ... I couldnt fit the original...

TBS Source One v3 GoPro Session 5 Mount 25 Degree. Use a LiPo Strap to fix the cam. ... Designed to use with this ND-Filter prints: https://www.thingiverse.com/thing:4337939 If i don't want to use an Nd-filter, i use an empty Nd-holder.

Caddx Tarsier camera mount designed specifically for the TBS Source One v0.3. The angle of tilt is precisely set at 25 degrees to ensure optimal viewing capabilities. ...A simple rotation of the model by 90 degrees in Fusion360 will yield a printable...

Runcam 5 mount designed for TBS SOURCE ONE V3 &nbsp;available in 25 and 30 degrees. Best printed on the side with supports and of course in TPU. ...If you want me to print it for you check out <a href="www.dlqfpv.com">dlqfpv.com</a></p>

A custom-built RX mount for the rear of the TBS Source One Frame is engineered to protrude from the back of the frame via plastic antenna tubes. ...Strategically fabricated in PLA, the mount securely fastens the RX to a sturdy plate using double-sided...

This is a set of rear mounts for the TBS Source One V3 that includes a frame designed for the iFlight GPS unit, an XT60 frame, and a DJI VTX antenna frame. ...I designed these because the placement of my VTX and capacitor limited my mounting options.

I had to adjust the 3D model since the 7-inch arms for the TBS Source One v0.1 are noticeably thicker, measuring around 6 millimeters in diameter. ...This made it impossible to use the 5-inch Arm Guards, which have a much thinner profile of...