tbs source one gopro mount 3d models

added a 45° angle for the SMA mount.

Skids are mounted using motor screws. Bumpers are press fitted. ... Using both skids and bumpers on all 4 arms will add about 16 grams of weight.

An adapter plate for Walksnail Avatar HD VTX. ...Has holes for M3 threaded inserts and holes for M2 screws and nuts for mounting VTX.Contains cuts for power cables to pass underneath.

Goes at the back of the quad under the top plate and uses the stand offs for mounting. ...Designed to fit perfectly with my rear bumpers and vtx antenna holder stl's

DIY

Simple Remix to incorporate an Immortal T antenna.Printed in TPU

Includes holes for fixing it with cable ties at the bottom. ...Crash resistant case.

A good, crash resistant case for the DJI Camera. No props on video! ...Fits on V1-V3

I designed this module for my long distance 7inch Drone, it extends from the rear of the body to provide a greater degree of seperation from othe electrical noises which could inhibit the compass. ... Also, my very first 3D design, feel free to...

First of all, thanks to roehrisch for their original design. Resized for narrower v4 frame in Tinkercad. Also added angled hole in the bottom for Immortal T wire to enter frame. ... This is the limit of my modelling skills :-D

Here is a remix for v4 / HD frame, with 25mm standoffs (25mm width, 30mm height). Thanks roehrisch for the step file ! ... PS: Grass was removed after i shot the photos, sorry !

<p>Its a remix of two models on Thingyverse</p>

Made it a snug fit 25x25mm size and added cutouts for zip-tieing the GPS

<p>Print in TPU, enjoy !</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Creality</p> <p class="detail-setting printer"><strong>Printer: </strong> <div><p>Ender 3</p></div> <p><strong>Rafts:</strong></p> <p>No</p> <p...

Remixed it because I was having issues with durability.thicker wedge thicker feet Make sure to print it on its face, if you try to print it on its side, at least with cura, the grain of the print will weaken the support and it will rip apart in...

Print on thermal printer, experience the thrill!

All I did was turn the bottom screw hole into a slot to allow for uptilt adjustability between 0 and 25 degrees for slower cinematic flying. ...Can confirm it fits the Foxeer T-Rex Mini and Razer Mini, but it'll likely fit other minis as well

Print temperature set between 214-220 degrees Celsius using Sainsmart or Yoyi TPU. Layer height adjusted to a range of .15 to .25 millimeters. Bed temperature maintained at 40 degrees Celsius. Raft and supports are not required for this print job.

To install this system, you'll first need to remove any standoffs from behind the FC unit and make a notch in the arm plate so that the camera wire can run underneath it. Next, use VHB tape to securely fasten the Air Unit to the bottom plate. You...

Print in TPU, enjoy !

Added a slot for a zip tie.

remix of TBS Source One V3 Gopro Hero 5/6/7 Reelsteady Mount by yani-yano February 04, 2020 not intended for reelsteady requirements!!! ...

gopro bones flap mount fits tbs nd filter

A one hand GoPro Mount for your bike. Attach the mount to your bike steering rod (stem) and simply take it out with one hand during your ride. Not made for extreme sports but for touring. ...

Simple GoPro mount for the MQC One. ...Print Settings: Rafts: They're completely optional Supports: Absolutely not required Resolution: A precise 0.2 millimeters Infill: With a dense 30% density

This kit converts your TBS Source Micro to a low-profile version. ...Utilize a 16x16 stack combo (ESC and Flight controller), a 14x14mm camera (Runcam Nano, Caddx EOS2...), RXSR or XM+ receiver, TBS Nano pro32 video transmitter, and some 1110 size...

It is made to fit the tbs source one v5 frame, mounted in the front just under the camera. It is a really tight fit, but that is exactly the way I wanted it. Print the parts, mount the antenna in the bottom base then super glue the top base on. Then...

Gopro TBS Mount for Caipirinha. ...This Is a Slightly Tight Fit, So Consider Scaling Up by One Percent or Two Before Printing.

This is a SpaceOne X220 with a custom-made soft mount for a GoPro, utilizing rubber gummy mounts between the two halves. Secure the bottom half to the top of the drone frame, then snap on your GoPro - you're now ready for flight! ...This setup...

I was unable to find a suitable GoPro mount for my Insta360 One, which is why I created this custom remix. Its design is remarkably simple and practical, perfectly accommodating my camera within its frame. To ensure durability, it's printed with TPU...