tbs source one gopro mount 3d models

I designed a small part to fill the gap between the frame's arms and base plates on my TBS Source One setup. This custom piece is tailored specifically for my V0.1 build but should also fit later versions since the arm mounts haven't changed...

It was specifically designed for use with the TBS Source One quadcopter frame. This GPS unit will also work well with other frames that have a similar spacer distance of approximately 30 millimeters. ... Printing this part takes about 27 minutes at a...

Mount for GoPro 10 for TBS source One V3 for printing in TPU

Custom made drone body shell (Skirt) for the TBS Source One frame. Made to use with 25mm standoffs. (images included have a gap due to 28mm standoffs) TechBytes.ca modified and printed for: https://www.youtube.com/c/thatguycarlos ...

... and replaced. 10.17.2021 - Added 6mm arm thickness version Printed bumpers for my TBS Source One V4 slim arms. Use zipties to hold them in place. This thing does not require to be held by the motor screws. Print with flex filament. ...

Note: Has to be printed in a flexible material like TPU to work. ... This version fits pretty snugly and stay put with its top lip design. I extended the end for additional motor protection. Designed for the TBS Source One HD frame arms.

Fits the TBS source one V5. A simple bumper to keep the bottom plate from being smashed up in a crash.</p><p>Print in TPU with the opening down and supports for the holes only. ...Use the printer settings that work best for your printer.&nbsp;</p>

**Note**: Has to be printed in a flexible material like TPU to work. ... This version fits pretty snugly and stay put with its top lip design. I extended the end for additional motor protection. Designed for the TBS Source One HD frame arms.

This is my upgrade designe for my TBS Soruce One V5

source one 11

## TBS Source One v4 Camera Mounts Various camera mounts for all kinds of FPV cameras for the TBS Source One v4 Supported Camera Sizes: - 19mm (Micro) - 21mm (Mini) - 28mm (Full) For every size there are two different mounts: one for short and one...

Some Shoes for the TBS source one V5 arms. Fit the 6mm arms well and have landing gear built in to save those motor screws. After seeing how others are using these turned the other way up they then protect the motor.  Only require supports under the...

Mounting system for DJI Air Unit + Tracer + DJI Antenna. ...Works with The TBS Source One V2&V3 Frame This design requires you to leave out the 3rd row of stand offs *Update , CRSF Nano version Available.

These are custom fitted parts to be printed in tpu for the tbs source-one v5 frame. The idea behind this skin is simplicity. As of now there is no hole for connecting to the fc. This is because new fc's have wireless connectivity. (update Ive...

Designed for TBS Source One. Will match other frame with similar spacer distance i.e.30mm. 27 minutes print time at 0,1 layer height, 0,2 will also work but print time if very similar on my printer.... ... Print Settings Printer Brand: Prusa Printer: ...

Source one V4 air unit mount designed to protect the mmcx, you will need to put esc lead front and use an xt60 holder on stand off and remap motors looks super clean

Custom made drone body shell (Skirt) for the TBS Source One frame.Made to use with 25mm standoffs. ...(images included have a gap due to 28mm standoffs)</p><p>TechBytes.ca modified and printed for: <a...

I took the original DXF file for the TBS Source One V4 (HD) arms and measured these things to fit exactly. I printed these in ABS for increased slippiness and durability compared to TPU or PLA but I didn't really abuse them yet so test whichever...

A cover to save the battery on a crash, for the tbs source one. Tested on PP where the battery survived a hard crash on the edge of a concrete ledge. A thicker version with with TPU should be also fine. Weight is around 26g in PP. Designed to print...

A cover to save the battery on a crash, for the tbs source one. Tested on PP where the battery survived a hard crash on the edge of a concrete ledge. A thicker version with with TPU should be also fine. Weight is around 26g in PP. Designed to...

Source One v4 Gopro TBS ND mounts ==================== For Session, Hero 5-6-7. Hero 8 and Hero 9. Preliminary. Designed for TPU FFF/FDM print. 20% infil. 2 - 3 layer wall. as of 2021-09-26 15, 20 & 25deg angle for most mounts. Please give...

Remix as I wanted the GPS to be attached to spacer and not above the frame. Compatible with Naze 32 GPS Ublox 7. GPS size without box is : 17,7x17,7x4,6. Designed for TBS Source One. Will match other frame with similar spacer distance i.e.30mm. 27...

Slammed Source One owners, listen up! This is a custom camera bumper designed specifically for your ride. ...Check out the attached Fusion file and get ready to take your photography game to the next level by redesigning this bumper to fit your unique...

I designed a battery pad to prevent my Source One's top plate screws from being damaged by the battery digging into them. Updated Version 2 includes two battery straps for added security. ...For an even more secure hold, use liquid tape on the battery...

This is a remix, for the TBS Source One V2. Added a 45 degree SMA to rear, added mount for nano Rx's. files are for standard 30mm tall or 20mm tall. ...Also added 20mm tall with 2200uf capacitor holder.

Advanced Power Module Source Two Battery Pad System

I've successfully printed two of these mounts, one in 0.35mm layer height and 20% infill which took approximately 15 minutes to print, and the other in 0.25mm layer height and 100% infill which took about 20 minutes to complete. The SMA connector...

The GoPro Hero5 Session NDFilter measures 36.5mm x 35mm x 1.7mm in dimensions. In comparison, the NDFilter Case measures 37mm x 35.5mm x 1.8mm in dimensions. This Runcam5 case is available with a TPU material option. The NDFilter case can be made...

I've sourced all non-printed parts from HobbyRC.co.uk, a reputable online retailer that's got everything you need to bring your quadcopter dreams to life. And let me tell you, it works like a charm. ...This thing flew around my garden like a pro,...

Modified top plate allows power lead to exit behind high-definition camera mount, eliminating unsightly wiring from frame's side profile. As a personal preference, I avoid power leads that protrude from the frame's sides. ...The custom-cut plates can be...