tasmota 3d models

Cooled by 2 Noctua Fans (one in, one out) and controlled by a nodemcu with Tasmota on it. One relay is managing the fan, a DHT11 is taking care of measuring temperature and humidity. Maybe later on i will share more details here, meanwhile if you...

I recently discovered the Blitzwolf SHP-6 with the Tasmota firmware as a perfect replacement for my old 433 MHz home automation system. Unfortunately, flashing the SHP-6 is quite tedious since it requires taking apart the entire unit and soldering...

- Import / export aquarium telemetry - On board Buzzer alert - Configurable alerts (water level, pH, temperature etc) - Outlets scheduler - Power consumption monitor (for enabled tasmota hardware) - OLED display - Temperature controlled internal...

1K Ohm resistor Black paint (acrylic seemed to work best; other paints that were thinner seemed to bleed into the fine seams of the plastic.) Currently, I'm using Tasmota firmware. You can use the LEDi setting which will illuminate when the switch...

Cooled by 2 Noctua Fans (one in, one out) and controlled by a nodemcu with Tasmota on it. ...One relay is managing the fan, a DHT11 is taking care of measuring temperature and humidity.</p> <p>Maybe later on i will share more details here, meanwhile if...

Alternatively, you can flash it with Tasmota using their instructions at [https://templates.blakadder.com/qs-wifi_D01_dimmer.html](https://templates.blakadder.com/qs-wifi_D01_dimmer.html). **Required Components** - Moes QS-WiFi-D01 Dimmer or Shelly...

You could also use Tasmota to do this if you do not want to use ESPHome. To fit this in nicely, all devices were powered with 3.3V headers. Pin D5 was used for PIR (including the GND and 3.3V adjacent) for an easy 3 pin connection. Pins D1 &...

More of a re-imagining than a remix as I redesigned from the ground up. Like the original this will use a 9g SG90 Micro Servo (I used these Miuzei brand ones from Amazon https://www.amazon.com/gp/product/B072V529YD/) I worked this up so that I could...

der abgespeckten ESP8266 Variante nicht so universell einsetzbar wie die Tasmota-Lösung mit SML Unterstützung. Die bisher gefundenen Gehäuse für den IR-Lesekopf nehmen nur die kleine, runde Platine auf mit 27 mm Durchmesser. Das ESP8266-Modul...

I have been flashing a few of my Sonoff S31 plugs to Tasmota using some spring clips instead of soldering on headers or wires. They work fine but are a little finicky because they get in the way of each other and I have to be very careful that they...

By means of rules in FHEM or TASMOTA, the air humidity can also be controlled automatically in conjunction with a humidity meter (e.g. <a...

I run Tasmota on the D1Mini, using the alarm output of the temp controller as a switch input. The temp controller's alarm is set to trigger when the temperature approaches the set point. When this happens, the D1Mini sends a signal to the smart...

1-1.5 meters or iron post or whatever can be found 1 Wemos D1 (not the mini) or an Arduino Uno, with Tasmota and activated stepper driver, has the advantage that it can be operated directly with 12 volts, or whatever can be found 1 Nema 17 stepper...

tasmota-DE.bin can be used. Reflashing is possible with the software Tasmotizer via USB micro cable. Be careful to really use a data cable here, which also has the necessary data line and is not just a pure charging cable!After selecting the correct...

I flashed the Sonoff Mini w/ Tasmota firmware (https://tasmota.github.io/docs/) (https://acoptex.com/wp/basics-project-109e/), but it could be used with the standard Sonoff Firmware and their eWeLink app, ESP Home, or other ESP8266 projects or custom...

You can find videos on YouTube explaining how to upgrade your firmware; just search for "How to Firmware Upgrade Sonoff WiFi Smart Switch" and ignore any Tasmota videos. Inching mode automatically turns the Sonoff switch on, pauses for the set time,...