tarkov labs keycard 3d models

Class Breakdown: 1st/2nd Class: - Explaining the project, allowing students to get into groups, brainstorming session, and 3D modeling a prototype 3rd/4th Class: - Finalizing the prototype, 3D printing the phone stands, testing them, evaluating...

I started down the rackmount home lab journey this summer and was looking to mount my existing SBC's (Raspberry Pi 4, Jetson Nano and Jetson Xavier NX). I found most of what I wanted in SliderBOR's RackPi project. But, I didn't have access to the DAP...

I also printed it in PETG with a high infill (I used 80%), 40mm/s speed and 1.2 layer height to improve dimensional accuracy and overall adhesion/strength NOTE: Triangle Labs Dragonfly is the Phaetus Dragonfly, they even reference it in their...

I use the exact same enclose to perform my hotted bench repairs : I simply disconnect the enclosure from the printer and connect it to my bench lab to heat up hotted, change nozzles, etc. - Must not let one connect a cable in the wrong place; -...

The creation of this model does not mean I endorse shooting narwhal for their tusks.The original tusk 3D scan was available, thanks to the Idaho Digitization lab. ...To get an impression of the animal, you can view the complete narwhal skeleton...

I could move equipment around the lab, or move my work to the equipment — OOOOOR I could make my own personal stirrer so that I never have to share equipment with anyone! I like that. A demonstration video of this mixer is here. This mixer is made...

Insert a washer and the butterfly nut:Go in the lab and measure the optimal rod length for your bench and position. The rods can be anywhere between 18cm to 50cm. Sizes shorter than 18cm might not allow full range of motion when installed under the...

I sliced using the Bambuu Labs slicer with the following customizations: Wall Loops: 4 Top Shell Layers: 9 Top Shell Thickness: .8 Sparse Infill Density: 40% If your slicer doesn't have these exact parameters just know that I was trying to make the...

The creation of this model does not mean I endorse shooting narwhal for their tusks.The original tusk 3D scan was available, thanks to the Idaho Digitization lab. ...To get an impression of the animal, you can view the complete narwhal skeleton...

Line Width/ Nozzle: 0.4 mmFirst Layer Line Width: 0.48 mm / 120%Average Speed: 20mm/s (First Layer) / 30mm/s (All the other layers) / 20 mm/s (First Layer) / 500 mm/s (All the other layers on Bambu Lab)Recommended Initial Layer Height:  0.16...

I use the Triangle Labs with a hardened .6 nozzle. It shouldn't matter what you have; thermistor and such are the same. * .6 nozzle. THIS CONFIG IS SET FOR A .6 NOZZLE. Change it if that's not what you have. Also, Cura profiles won't help you. Check...

It was designed by Bell Labs' Nike team, and was initially based on the earlier Nike Hercules anti-aircraft missile. https://en.wikipedia.org/wiki/Nike_Zeus https://www.mda.mil/global/documents/pdf/zeus.pdf The Spartan ABM evolved from the Nike...

I am starting to build my motion simulator based on SimLab GT2 https://sim-lab.eu/product/gt2-sim-racing-chassis/ racing rig. It uses two motors and controller box. Here I will post all the stl files that i have used and also other source files if...

This is a simple electric motor powered by a single AA battery that's perfect for science classes, physics labs, or fun weekend projects with your kids to demonstrate basic principles of electromagnetism. The motor uses inertia and magnetic...

... will have learned why that force is there. In order to get a grade, the student will fill in a paper describing how it works, how well it works, and how long it took them to make it. The paper should be like a science lab report over the gyroscope.

Could there be a better time for the 3D lab of the NHM Vienna to present a small collection of cookie cutters? Probably not, which is why the fairy lights have been running hot and we are now proud to present our “ready to 3D print” cookie...

Could there be a better time for the 3D lab of the NHM Vienna to present a small collection of cookie cutters? Probably not, which is why the fairy lights have been running hot and we are now proud to present our “ready to 3D print” cookie...

Could there be a better time for the 3D lab of the NHM Vienna to present a small collection of cookie cutters? Probably not, which is why the fairy lights have been running hot and we are now proud to present our “ready to 3D print” cookie...

Could there be a better time for the 3D lab of the NHM Vienna to present a small collection of cookie cutters? Probably not, which is why the fairy lights have been running hot and we are now proud to present our “ready to 3D print” cookie...

Could there be a better time for the 3D lab of the NHM Vienna to present a small collection of cookie cutters? Probably not, which is why the fairy lights have been running hot and we are now proud to present our “ready to 3D print” cookie...

Could there be a better time for the 3D lab of the NHM Vienna to present a small collection of cookie cutters? Probably not, which is why the fairy lights have been running hot and we are now proud to present our “ready to 3D print” cookie...

Once you've stroked the crank 12 times the camera will require you to reset the frame counter before shooting further.For the second go around, advance one stroke per frame.For the final go around the frame counter, advance 0.75 of a stroke for each...

Here's what I've got: Note this list will change shortly Beer_Tokens_Tray_v2.3 Holds 6 sets of beer tokens, along with medal Print 4 times Dollar_Rep_Tokens_Tray_v1.1 Holds $1/$5 and 1/5 rep tokens Print 1 time Player_Upgrades_Tray_1-2_v3.1 Holds...

My sleek take on an ATX PSU to lab bench power supply. Follow the RepRap ATX to power supply (PSU) conversion guide for directions and warnings. There seem to be plenty of PSU conversion cases/fittings here so why did I upload mine: 1.) I prefer...

I have been working on cleaning up my lab bench. To this end, I wanted to get my wire rolls off the bench. This makes it easier to use the rolls.</p><p>A similar solution would work for solder spools.</p><p>Pictures show this mounted to my shelf, but...

I wanted to have both a powerbank and a mobile lab power supply which are also protected by a corresponding housing, in this case the ammunition box, waterproof.I wish you a lot of fun and success in rebuilding...

Power it from PC's USB connector.Charge your batteries from a lab power supply. Use this method ONLY if you know what you are doing. I used this method to simply charge some cells to Storage Voltage of 3.8V, where current is limited to 0.5A in CC...

Developed at the MAGIC ACT / e-NABLE Lab at Rochester Institute of Technology, the Explorer Thumb TD has evolved over the past year to be effective for many multiple-handed tasks in much the same way as the voluntary opening split hook that has been...

I created this device to consolidate ten individual power bricks for each compute node in my home lab into just one power supply, allowing me to clean up the wiring, reclaim space, and free up several outlets on the power distribution system in my...

This is meant to be for labs and companies. Printed in PLA they are cheap, durable, reusable and chemically resistant.</p><p><br>Feel free to leave me feedback and suggestions and let me see your prints, I'm curious. Also I won't print all of the...