tamiya tt 01 3d models

The M-01 and M-02 models from Tamiya's line of R/C cars feature a unique front bumper design that sets them apart from other models in this category. ...This distinct design element is more than just aesthetic; it serves an essential purpose in the...

This part covers a hole in the Tamiya TL-01 chassis that was originally intended for a mechanical speed controller's resistor. This should reduce the amount of dust ingress into the chassis (at least into the rear). ... Requred hardware: - 2x...

This is a mounting bracket for installing a Smartibot board onto a Tamiya CW-01 chassis, which can be found in models like Lunchbox and Midnight Pumpkin. ...It enables you to control your model using the Smartibot app instead of a standard R/C system,...

The cover is fixed with one screw. ... The cover is for this Tamiya DT-01 servo mount : https://www.thingiverse.com/thing:5003913 One Design is with a Hole for Cable. I do not use this hole for cable. Printed in PETG. ...0.2mm

Made this conversion for the M-01/M-02 from tamiya to fit a modern lipo battery because i don't wanted to buy extra stickpacks. I made a fusion out of an M-01 and an M-02 to drift with double motor. The conversion does work for all M-01 or M-02...

These are Tamiya TL-01 front lower suspension arms. Please take note of your printer's tolerances, they are crucial to get this dimensionally accurate. These are designed to be a tight fit to eliminate the usual Tamiya play. You may need to run a 3mm...

These are some simple side steps for a Tamiya CC-01. They are designed to fit the Isuzu MU body - some of the dimensions may need to be adjusted for other bodies. They bolt on using existing screw holes (be careful with the length of the screws in...

This is a spare wheel mount designed specifically for the Tamiya MF-01 Suzuki Jimny model.\nThe adapter features an M3 nut located internally, accessible from the rear side.\nA M3 bolt can be used to secure the wheel firmly in place.\nIn addition,...

To address this issue, I have developed an alternative long arm set that replicates the geometrical results of the original Tamiya set while utilizing most of the stock TL-01 parts. This set requires only one additional M3x20mm bolt per arm, which...

So i've developed this alternative long arm set that gives you the same geometrical end result of the original Tamiya set while reusing most of the stock TL-01 parts. You only need one extra M3x20mm bolt per arm, which are cheap and easy to find at...

A set of rear lower arms for the Tamiya TL-01 has been designed. Two extra shock mounting positions have been added, allowing you to fine-tune your suspension settings even further. Please take note that your printer's tolerances play a crucial role...

The Body of my Tamiya FF-01 (Volvo 850 Body) didn't fit perfectly, its rear wheels were a little bit too far forward. I didn't want to cut the really nice body, so I decided to design a rear suspension that's 3mm further back - which is enough for...

Shock mounting brackets for the Tamiya TL-01. My chassis had cracks in all four shock mounting areas, so I created this part to reduce the stress to each point by spreading the load. It also places the shocks more upright and makes adjustments to...

Front servo mod for Tamiya CC-01. This design allows the servo to sit at an angle, eliminating the need to amputate the entire front end of the chassis. The servo bracket is self-supporting, while the top brace requires additional support. Using...

You can find STL files to replace the XV-01 triangles from Tamiya in the link. Be sure to align the axle housings and tap the threads of the screws that block the axes. I've been running with printed triangles for three years now in RC RALLYE...

For T3-01.

If you have a Tamiya TL-01 chassis R/C, are not using the old school mechanical speed controller with a ceramic resistor and want to plug the hole this is for you. These plates fit the TL-01 early and later model chassis variants. The early one has...

TAMIYA CR-01用。簡単なバッテリーホルダー、あなたの車に合うようにウレタンなど入れて厚さを調整して下さい。レイヤー高さ：0.2mmインフィル：20％サポート：必要ビルドプレート密着性：ラフトが良い

Support for Tamiya CR01 crawler servo.\nThe high suspension arms are the central and distant mounts.

A set of rear lower arms for the Tamiya TL-01. I've added two extra shock mounting positions so you can tweak your suspension a bit more. Please take note of your printer's tolerances, they are crucial to get this dimensionally accurate. These arms...

This is a Tamiya TL-01 front upright C-bracket designed to replace the original part. I have also included versions with 2 degrees of caster and one with a hole in the top of the bracket for a ball joint. Added a 2 degrees of caster version, along...

For those who prefer the single A-arm suspension, which is a hallmark of the CW-01 chassis, this steering knuckle is designed for the Tamiya chassis (Lunchbox, Midnight Pumpkin, Unimog...). The knuckle features an arm that's thicker than its...

This upgrade is designed to enhance the stock Tamiya CC-01 with a few modifications that use existing hardware, except for a spacer placed at the knuckle to elevate the ball joint (see attached image). Instructions: Remove the stock steering and...

I ordered one more set of these gears from Tamiya, but I've had enough waiting. Now it's time to try making them myself. Also, the printed gears are working perfectly with the Tamiya ones. This means if you damage a Tamiya gear, simply print a new...

3D printable on-road RC car Rim/Wheel for Tamiya 1:10 tires/models https://www.youtube.com/c/mfactory33 Rim Diameter: 52mm Rim Width: 26mm Designed in blender For more Rims go to our website: www.mfactory33.com

3D printable on-road RC car Rim/Wheel for Tamiya 1:10 tires/models For more Rims go to our website: https://www.mfactory33.com Rim Diameter: 52mm Rim Width: 26mm Designed in blender 3D PRINTING SETTINGS Layer height: 0.19 We print these with ABS...

Much stronger front suspension tower for Tamiya XV01 chassis mostly design for Rally cars. Recommended material is something stronger, more technical such as ABS+, ASA, Nylon-CF, Polycarbonate or really hard TPU. ...I used 65 mm suspension...

I broke my C hub on CC-01 and here is to download. it´s Left and right side versions. ... Printing Time: 60-180mins

This is an updated CC-01 rear axle carrier to be used with custom 4-link suspension. ... I found the rear stock suspension to be rather lacking on the CC-01, so I made these to be used with various length linkages. ... Good luck!

This is a simple cockpit-inlay for the nice Tamiya Crawler Rock Socker.It is based on an “Recaro-Seat”model of https://www.prusaprinters.org/prints/104072-recaro-seat-without-the-base , but heavily modified.Maybe, it fits on variants also, I don't...