tamiya tt 01 drift 3d models

For T3-01, replace the screw with a longer one.

Discover the Tamiya TT-02 Drift Chassis, a versatile and high-performance racing kit designed for drift enthusiasts! This 4WD chassis boasts a lightweight yet sturdy construction with low-polycarbonate side shields, making it perfect for drifting...

You can attach RC universal headlights to the front bumper of the CC-01 with this holder. These lights are available for purchase on eBay, for example at...

Two Piece Wheel in Steel Finish Outer Diameter Approximately 2.1 Inches Width Approximately 1 Inch Wide Offset Approximately 0.5 Inches 0.47 Inch Hex Bolt Typically Used on Original Tamiya TT01 Tires Aesthetically Determines Also What Kind of Hitch...

... offset narrowness comes in at 16.6mm. A 12mm six-sided bolt pattern is standard. This type is typically used for original Tamiya TT01 tires. ...In terms of appearance, this design also influences what kind of couplers and trailers can be attached.

I crafted this drift tire using AutoDesk 123D Design, and it functions incredibly well. Check out the video to see its impressive performance! ...https://www.youtube.com/watch?v=1P8rxFtw1dM&list=UUXilNPFTRF2KxeNoi_gZeyQ

I meticulously crafted this cutting-edge drift tire within the versatile design platform of AutoDesk 123D Design, and I'm thrilled to report that it operates flawlessly. Take a moment to witness its performance in action - watch the video for...

This is the damper stay I created for both front and rear for Tamiya's TT-01 Type E chassis. Based on other mod that gives more clearance and suspension travel space, this damper stay will allow you install 70mm dampers gives stabilities. ... Video:...

I customized a compact Tamiya Ta-01 chassis to perfectly accommodate the sleek Tamiya Beetle body shell.

Tamiya TT chassis rim / Felge "Porsche Fuchs Design" 13 different rims with the legendary 5 Star Offset from +8 to -4 in 1mm step dia 52mm, width 26mm fits for Tamiya TT chassis and many others...

Revise Tamiya's M-01/M-02 front bumper to the advanced E2 version.

Designed this to have a Handle on the Car. It bugged me to always hold it by the Tires or the Axels. It's not perfect and i may do some changes. But for now it works and its ok. ... Perhaps I will do changes after a day or two where it came to use.

Servo protection box for the Tamiya XV-01 chassis. ... Edit: Updated to v3 (higher box to prevent servo horn touching)

This model contains Tamiya CC-01 front lower arm, front knuckle and C-hub (left side) and the front wheel axle.

Tamiya CC-01 Side Bars, a precision-engineered component designed to amplify the off-road capabilities of this highly sought-after RC truck model.

This model contains Tamiya CC-01 front lower arm, front knuckle and C-hub (left side) and the front wheel axle.

A set of front and rear body posts for Tamiya TL-01 on-road chassis cars. These parts C5 and C20 from Tamiya 50737. This design is based on guess-timations since I don't have the real part to measure. However, I have printed them and tested...

A set of front and rear body posts for Tamiya TL-01 on-road chassis cars. These parts C5 and C20 from Tamiya 50737. This design is based on guess-timations since I don't have the real part to measure. However, I have printed them and tested against...

Custom motor plates enable users to modify the gear ratio of their Tamiya TT-02 chassis beyond what's possible with standard factory mounts. ...These parts can be printed without the need for support structures.

My creation for body shell post mounts for 1:10 scale rc car, either electric or nitro.Installed on my Tamiya TT-02.My other design for standard body post mounts: https://www.thingiverse.com/thing:6273432

A replacement for the Tamiya TL-01 part B3 (from Tamiya part no. 50736). I recommend drilling the screw hole with a 3.2mm or 1/8in drill bit so that the screw will only thread into the chassis. ... Required hardware: - 1x M3x10mm or M3x8mm screw The...

A replacement for the Tamiya TL-01 part B3 (from Tamiya part no. 50736). I recommend drilling the screw hole with a 3.2mm or 1/8in drill bit so that the screw will only thread into the chassis. ... Required hardware: - 1x M3x10mm or M3x8mm screw...

Tamiya T3-01 dancing rider original plastic parts a bit crispy and i didnt want to buy new parts, came up with a solution to print fixing part, so far so good.

This gearbox is designed for Tamiya CC-01 chassis and features a 15T/29T pinion setup with a gear ratio of 0.51724. ...The total gear ratio of this 540 motor model, sourced from Richard Baldock, is 1:28.362.

Here is a simple design of the upper and lower front suspension arms from a Tamiya WT-01 RC car. ...I wanted to make my WT01 4WS and decided to design and print the parts.

Tamiya CC-01 stand. Both parts must be printed twice. In the pictures, one half of the stand is made of PLA, the other of PETG. ...(I ran out of pla)

My debut creation unfolds as a precision-made accessory holder, custom-designed to securely fasten the iconic Tamiya TT-02 chassis in perfect harmony with a ruggedized GoPro camera mount. ...To bring this innovative design to life, you'll need one...

A servo mount for Tamiya TL-01 chassis. Greatly reduces the servo's ability to wobble in its mount. ... The STL is designed for a JX 4409MG servo, but may fit others with a length of ~41mm and width of ~20mm.

A servo mount for Tamiya TL-01 chassis. Greatly reduces the servo's ability to wobble in its mount. The STL is designed for a JX 4409MG servo, but may fit others with a length of ~41mm and width of ~20mm. ...

This is a small bracket for the Tamiya TC-01 that allows you to place an antenna tube inside the air scoop cavity of the lexan body. ...You will need two short ~3mm screws to bolt it to the gear case.