tamiya grasshopper and hornet battery cover by 3d models

I've Built an Accurate Model of the Fabled Battery Cover on My Tamiya Grasshopper and Hornet. Breaking those infamous battery covers has been a rite of passage for many modelers; I know firsthand that agony, so here's my solution - an accurate 3D...

Needed a new Motor/Gearbox cover for my Grasshopper II as the part was lost by the former owner. As I have not been able to find a file I decided to make my own design. Did three different versions: -> a flat one -> one with hole in the center ->...

remake of the original battery cover of the tamiya grasshopper/ hornet,...

tamiya grasshopper hornet bumper test type-A little fix Correct the elliptical part to a perfect circle

I designed this light because, once I flipped my hornet the light fell of. ...I am sure this has happened to allot of people.

I designed this light because, once I flipped my hornet the light fell of. I am sure this has happened to allot of people. ...Print Settings Printer Brand: Creality Printer: Ender 3 Resolution: 100 Infill: 50% Filament: Tinmorry PLA Any colour ...

... on Thingiverse: 3250898. If you need to purchase the original parts, search for Tamiya C Parts 58416 Grasshopper II / Super Hornet / Rising Fighter (0555115). ...The OpenSCAD source file is included so you can adjust some parameters to your liking.

Part broke off so designed replacement. Should fit the default M3x8 self-tapping screw Goes well together with the battery cover by @Pedro34 https://www.thingiverse.com/thing:3250898 If you want to buy the original parts tree search for: Tamiya C...

1) grasshopper front suspension upgrade parts (MK1, old design, using original spring) https://www.thingiverse.com/thing:3860829 2) grasshopper rear suspension upgrade parts(MK1) https://www.thingiverse.com/thing:3815254 3) grasshopper driver figure...

... has been upgraded to Hornet rear suspension. If you have a Grasshopper with the Hornet trans and sliders, we can upload a version with the needed battery retainer. Please refer to the video below for the installation. ...https://youtu.be/zq1o9Wb2qB8

1) grasshopper front suspension upgrade parts (MK1, old design, using original spring) https://www.thingiverse.com/thing:3860829 2) grasshopper rear suspension upgrade parts(MK1) https://www.thingiverse.com/thing:3815254 3) grasshopper driver figure...

Servo Mount for a Tamiya Grasshopper chassis, I didn't like the original ones so made this to give the steering servo a little more rigidity

... So this is more an experiment, but it works. I took 2 soft springs, length around 25mm and around 10mm in diameter. Maybe you have to try different springs, don't make it to hard. Try at your own risk... ...;-) I used PET, PLA will break.

... So this is more an experiment, but it works. I took 2 soft springs, length around 25mm and around 10mm in diameter. Maybe you have to try different springs, don't make it to hard. Try at your own risk... ...;-) I used PET, PLA will break.

This stand is designed specifically for Tamiya's Hornet and Grasshopper models, but its versatility suggests it can also accommodate other vehicles with similar dimensions.

... For the additional wishbone, I simply used a M2 Rod End purchased at my local Hobby shop. Check out the pictures. I believe these parts could also fit the Tamiya Hornet, which uses the same chassis. ...However, I do not have one to test it.

1- use bent rod ends with a straight threaded rod(easiest) 2- Use some M3 threaded rod and bend each end approximatly 45° to use with regular rod ends(this is how I made theones in the pictures and video. Special note... If you want to use a Silver...

... fall off. If you have an early hornet with the "tab" on the transmission from the Grasshopper, you will need to cut it off and smooth it out. ...Please see the video prior to purchase.  Battery Door and Retainer Installation youtu.be/fcEEeqy0nL8

Replacing the battery door on a Tamiya Super Hornet model requires some finesse, especially when it comes to printing the base. To ensure a smooth and successful print job, it's recommended that you rotate the design 180 degrees before printing. ...This...

This is a set of 2.2 dish wheels that I designed for use on the Tamiya Hornet, Grasshopper, and Frog. ...I print them at 100% infill and 0.1 layers.

This is a set of 2.2 dish wheels that I designed for use on the Tamiya Hornet, Grasshopper, and Frog. ...I print them at 100% infill and 0.1 layers. Category: 3D Printing

Here are one-piece wheels perfect for vintage Tamiya 1/10 RC buggies such as the Hornet, Grasshopper, Frog, and more. These wheels fit the original tires precisely and serve as a direct replacement for the stock wheels. ...I've printed them in nylon,...

Adjusted the diameter to synchronize it with the 21mm dimension found on the Hornet, Frog, Grasshopper and Hotshot Falcon engine models.

You have to use the old 5 pin style drive hub found in the kit or print a set of them from here: https://www.thingiverse.com/thing:4159329 These are the same as my wheels for the Hornet but with a different rear offset to suit the Grasshopper 2/II....

... ...You have to use the old 5 pin style drive hub found in the kit or print a set of them from here: https://www.thingiverse.com/thing:4159329 These are the same as my wheels for the Hornet but with a different rear offset to suit the Grasshopper 2/II.

This is a custom replacement spoiler mount and spoiler designed specifically for the Tamiya Hornet. The spoiler mount is engineered to attach directly to the factory chassis, seamlessly integrating with the slots in the standard body. Printed at 100%...

I'm currently giving my trusty old Tamiya Hornet a thorough makeover, but I've come across a problem - the part I need is nowhere to be found, so I decided to create one myself. ...If you'd like to take a closer look at it, feel free to edit it online...

This is a headlight and tail light enclosure for LED lights I purchased for my old Tamiya Hornet. The headlights are slanted down so they light up the road in front of it. I printed mine with white PLA, which in retrospect was not a good decision...

This brace will prevent the transmission from "slapping" under acceleration and still provide maximum articulation. This also improves the suspension travel on the Super Hornet. ...Please see the video below for the installation.    ...