talon claw holster 3d models

This modification significantly enhances the performance of the Talon Claw without requiring a machined ram. Using this ram in conjunction with two O-rings and half of a K25 spring allows me to achieve approximately 150 FPS. ...I've included SketchUp...

This particular claw was designed to replace the default claw found on Black Point Tactical IWB holsters, which rode above the belt and failed to keep the holster in place and the grip against the wearer. ...The claw uses the holster's existing screws...

I noticed that the original grease covers by ed_wolfe91 didn't fit on my talon claw, so I redid them from scratch and made them a little more printer friendly. Print in given orientation, no supports. The holes still need to be drilled. ... ...

This is an adapter to use a airsoft buffer tube on your talon claw. I would not attempt to print this unless you have a well tuned printer. Printed successfully in HTPLA+ at 240C / PLA+ at 225C, 0.2mm layer height. ... min 5 perimeters.

I wanted a simple silencer for my talon claw, but a chunky one, couldn't find a design I liked so made this. This is based on the worker design. Designed to fit talon claw barrel. Internal diameter is 16mm, my print is 16.1mm but it wasn't a press...

A simple yet styled magwell rail riser for the Talon Claw U. Good for those who want to mount a sight yet find the stock rails too low. To fix it in place you'll need a threaded rod. If you have a threaded rod for the railgasm couplers already,...

I liked Radiosilence187's Thumbstock remix but didn't want to swap out the rear-butt section of my Talon Claw. I wanted a way to incorporate the Thumbstock spacer without modifying the end section. These files will allow you to do just that - no...

Human: Essential components for installing brass into your Talon Claw are available below.\r\n\r\nThe muzzle must be printed with robust walls to prevent premature wear on the clamp feature.\r\n\r\nThe rambase needs to be printed sturdy enough to...

This particular claw was designed to replace the default wedge found on QVO Tactical IWB holsters, which rode above the belt and failed to keep the holster in place and the grip against the wearer. ...The claw uses the holster's existing screws and...

The adapter will securely accept a mil spec AR-15 buffer tube, allowing you to mount any AR stock directly onto your talon claw. In my test print, the threading provided a remarkably tight grip on the tube, rendering the castle nut unnecessary;...

https://www.prusaprinters.org/social/114667-racerethan/prints Update 12-4-20: Added a modified doom shuttle that has a longer rail for the Pryangle Grip Doom Shroud Shortened to Talon claw V4/ Full length size. Use the caliburn muzzle6 for the...

Hello, this is an enhanced version of the pump grip handle designed specifically for the bull-pup model of the U-Channel Talon Claw created by Captain Slug. I've integrated tabs along the side of the handle that smoothly glide along the inside of the...

Update 12-4-20: Added a modified doom shuttle that has a longer rail for the Pryangle Grip Doom Shroud Shortened to Talon claw V4/ Full length size. Use the caliburn muzzle6 for the front. The bottom 2 threaded rod may be longer than what is given in...

Uses the same hardware kit as the normal Talon Claw U Bullpup, along with a Caliburn plunger rod cut down to 5 inches, and a caliburn o-ring set for the small plunger o-rings. The hardware kit requires some minor modifications. Assembly instructions...

Remix of Slugs Caliburn/ Talon Claw u-channel parts. (The Remix source in Thigiverse is not working, I will add the original source once it does) 2 version: 1. Files with a 1 at the end use prime rods that are angles. They MUST have both ends...

A Raider magwell for the Talon Claw U. This kit replaces the entire magwell area of the TCU, as well as the foregrip. To make this kit left handed, simply mirror the parts in your slicer. To make this kit compatible with my printed U channels,...

Remix of Slugs Caliburn/ Talon Claw u-channel parts. (The Remix source in Thigiverse is not working, I will add the original source once it does) 2 version: Files with a 1 at the end use prime rods that are angles. They MUST have both ends drilled...

Non-printed parts: - 2 4-40 screws (1 and a takedown pin for the takedown version) - A Talon Claw length threaded rod (25cm) (goes over the plunger tube and keeps the slamfire kit in place between the magwell and the back of the plunger tube) - A...

Non-printed parts: - 2 4-40 screws (1 and a takedown pin for the takedown version) - A Talon Claw length threaded rod (25cm) (goes over the plunger tube and keeps the slamfire kit in place between the magwell and the back of the plunger tube) - A...

This is based on the Talon Claw U by Slug, allowing users to integrate a Super Core made by Spectre's Workshop into their build. Print at .2mm, with no supports needed for this project. The files provided include all components except the mag side...

This is a stock for the V3/V4 talon claw that I designed for my specific play style. I dont need an adjustable stock, and I wanted one that was solid and trustworthy. This has a Buffer-tube-esque look, but uses the original buttplate . This will...

The adapter will accept a mil spec AR-15 buffer tube so you can mount any AR stock on your talon claw. In my test print the threading gripped the tube very tightly so the castle nut was not necessary but if you print with more clearance you might...

Just the files that are different than a non-takedown Talon Claw. Same hardware etc. The front cover is a long print. To get the detail in the PLA I used a .2 print and went slow since it is tall, took 22 hours to print. Just an FYI. You can use any...

Update 12-4-20: Added a modified doom shuttle that has a longer rail for the Pryangle Grip Doom Shroud Shortened to Talon claw V4/ Full length size. Use the caliburn muzzle6 for the front. The bottom 2 threaded rod may be longer than what is given in...

IT HAS BEEN REUPLOADED HERE: https://www.thingiverse.com/thing:4898355 A Raider magwell for the Talon Claw. This kit replaces the entire magwell area of the TC, as well as the foregrip and muzzle. I recommend you print this at 70-100% infill with...

I'm sharing just the files that set my Talon Claw apart from its non-takedown counterpart, with all hardware identical. The front cover features a long print to capture intricate details in PLA. To achieve this level of detail, I employed a .2mm...

... forward and get a smooth operation. Edit: I've finally assembled one and it performs flawlessly. Photos have been added. Edit: A thick Talon-only magazine release is available that matches the thickness of the Slugs' trigger guard perfectly.

A set of mag releases for the TalonClaw and TalonClaw U that allow you to just pull out the mag, like a Worker Talon adapter. Demo video: https://www.youtube.com/watch?v=dnQnLgC5GLw If you wish to print and sell this item, please contact me for...

... After finally assembling one, I'm pleased to report that it functions exceptionally well. Photos have been added for reference. Edit: There is now a thick Talon-only mag release available, which perfectly matches the thickness of the trigger guard.