tacx t3050 spider 3d models
10778 3d models found related to tacx t3050 spider.
thingiverse
This is a spare part for a Tacx Team Sprint bicycle repair stand (T3350). It replaces the original bushing for 15mm x 100mm achses (front wheel). For reasons I coud not slice it with Cura. Cura sees some surfaces wher no surface are and want to...
thingiverse
... to extend the lifespan of worn-out components. ...Engineered with durable materials such as PET-G and ABS, these parts ensure long-lasting performance with 100% infill density. I've been working with an older Spider workstand from approximately 2008.
thingiverse
Supportive brackets are installed on the bicycle's bottom frame to secure it firmly onto the stand.
thingiverse
Increase the original Tacx Front Wheel Holder by swapping out four parts. ...First, remove the existing rubber inserts and then reinstall them at the base of the component.
thingiverse
With the need to make the TACX FLUX S roll higher, I developed these shoes to raise approximately 20mm from the ground. ... The rear shoe is made for support only without fixing.
thingiverse
These hooks are for mounting bike rollers vertically on the wall. ...They are left and right handed with a slight chamfer in each to match the tapered drum on the Tacx Galaxia rollers they were designed for.
thingiverse
It fixes directly into the 50mm aperture in the Tacx trainer (you need to remove the small circular guard in the centre of your trainer - it just pops out). The push-fit on the STL file is at exactly 50mm diameter - if it's a loose fit, just wrap...
thingiverse
Remix of the Tacx Disc Remover by Sutnop. My printer sometimes under extrudes, so this design uses more filament but its sturdier. Haven't had an issue (used it multiple times), hopefully you will find it useful. ... You will need a M16 nut (60mm...
thingiverse
Another version of the Tacx Neo Disc Extractor The advantage of this one is that no spanner is needed. Works perfectly (used it a few times already). ... You will need: M16 bolt 80mm length M16 nut 3 x M6 bolt 90mm length + washer + optionally...
thingiverse
The feet of my (Garmin) Tacx Cycle Motion were broken. I decided to print new ones. To make it a perfect fit, print it with a scaling factor of 101%. I also designed a new bottom bracket support. ...Check my other things on Thingiverse.
prusaprinters
This is a replacement foot for the TACX CycleTrack cycle trainer. ...I have been unable to source these anywhere unless I buy a second hand unit!</p><p>The print is in two parts with the insert requiring minimal support material, the two pieces need to...
thingiverse
Designed to eliminate noise in my Tacx Neo, I crafted a custom removal tool from scratch. Disassembling the unit with care, I wiped down and sanitized its interior using a gentle wipe and pure alcohol solution. Now, it runs completely silent once...
thingiverse
This thing is to help the internal fan of your Tacx Neo (every edition!) to get rid of the heat. After reading so many complains about overheating Neos I decided to design a fan mount which helps the neo to suck air out of the housing to prevent...
thingiverse
The Tacx Spider Team Repair Stand (T3050) requires a thru-axle adapter. The dimensions specified are suitable for 12mm × 100mm thru-axle forks, but the 3D file can be easily modified to accommodate other sizes. ...For further information, visit my blog...
prusaprinters
This thing is to help the internal fan of your Tacx Neo (every edition!) to get rid of the heat. After reading so many complains about overheating Neos I decided to design a fan mount which helps the neo to suck air out of the housing to prevent...
thingiverse
Smaller screw for Tacx Flow smart. ...For some bikes the original screw is too big.
thingiverse
Pedal for Tacx Flow Smart, print with support from ABS, Outline 3mm, up/bottom layer 2.5mm, infill 20% gyroid
thingiverse
Replacement pin for Tacx Dao Bicycle Bottle Cage. Printed in ABS. ... 2023-06-25 Updated version 1.1 with thicker tab and shorter pin at the top.
thingiverse
Adapted from another model for the Kickr Core that I cannot see how to attribute it to. ... This is the rear rocker foot for the Tacx Flow.
myminifactory
The original Tacx "tablet mount" was too big to hold both my Note 4 and the Asus Zenpad, so I designed alternative mounts after taking online measurements. The Samsung Note 4 and Asus Zenpad versions fit perfectly, while the rest of the designs were...
thingiverse
This is a very simple fan mount to attach a 50mm fan with 40mm distance for screws to the ventilator slots on the drive side of Tacx Flux trainers. I made it for the Flux S, but it should fit for the other variations of that model (non-S, 2...). ...
myminifactory
Just got my TacX Neo Smart trainer and wanted to mount my Samsung Note 4 or/and 7" Asus Zenpad in front of me on the handlebar to use it as a Zwift controller. To do this, I used the original "tablet mount" accessory from Tacx and my Garmin mount for...
thingiverse
This is extented arm for Tacx tablet holder and is remix from https://www.thingiverse.com/thing:2228433 In this remix I have deleted the embossed text in order to protect the back cover of tablet. ... The corner part that holds the tablet in place was...
thingiverse
To install the mount, simply slide it over the Tacx Flow Smart trainer and secure it in place with a cable tie if desired. I have designed the mount to include a raised rim that keeps the cable tie organized and out of the way. Power up the fan,...