tacoma rc 3d models

Introducing the 2019 Model Toyota Tacoma with an intricately detailed exterior and simplistic interior. The car features four wheels strategically positioned at each corner. Textures are included, while a separate zip file is also available for your...

1/1800th scale Tacoma class frigate model. Some components intentionally oversized.\n\nTacoma-class comprised of ninety-six US Navy frigates based on the British River-class design, armed with three three-inch guns and assortment of anti-aircraft and...

Simple design to mount phone in tacoma 3rd gen. Just use 3m "extreme" double side tape to stick magnet mount linked below. The phone case I am using (linked below also) has metal infused into it so there is no need for the classic metal plates most...

I created this based on the idea I found in the 4Runner and adapted it for use with my 2nd Gen Tacoma (2009). I built using PLA at a 0.2mm layer height, and it looks fantastic. I would recommend four solid top and bottom layers and two to three...

Hello, if you are working on upgrading your first gen tacoma like I am you may like this. I have designed a switch panel to go where the cubby bellow the head unit. it fits great and looks amazing. I designed this panel to use these switches from...

The iPhone 4/4S dock for a 2009 Toyota Tacoma mounts in place of the passenger airbag switch using an Apple 30-pin to USB cable. Suitable for iPhone 4 or 4s with case, the iPhone 5 version is available here: http://www.thingiverse.com/thing:40254. To...

Print out 12 pieces of TPU from your preferred source, then remove one side of side-steps from a Toyota Tacoma, ideally a 2020 model but likely applicable to those as far back as 2012. Next, use a mallet to knock the TPU pieces into the empty M8 bolt...

This is a Dash Cam mount for a 2013 Toyota Tacoma. It mounts a SJ4000 camera (may fit GoPro's) discreetly up behind the rear view mirror. The mount clamps to the rear view mirror post and uses a few 4-40" Screws and Heat-Set inserts for mounting. ...The...

On the 1996-2000 Toyota Tacoma, an access panel below the headlight must be removed to remove the headlight housing, as shown in the picture. The small metal rectangular panel is held in position with a sheet metal screw and a plastic retention...

Mount for a Tekonsha Prodigy P3 trailer brake controller to fit in a first generation Toyota Tacoma (1996-2004). The fuse panel cover replaces the cover for the fuse panel under the dash with a print-in-place rotating latch. I designed the hoop with...

Cup holder divider for second-generation Toyota Tacoma owners. When I purchased mine, it surprisingly didn't come with this crucial feature. Since I didn't have XM Radio, I decided to take matters into my own hands and modify a design from...

Mounting a colorful TRD emblem on the grill of a 2022 Tacoma is next to impossible using the retainer that came with the product. The badge is too large to fit comfortably inside of a “honeycomb” and would have to be mounted protruding outside of...

I installed the RedArc brake controller in my Gen 2 Tacoma by cutting out a center console blank plate, but it wasn't an easy task. My brother-in-law then got the RedArc for his Gen 3 and since I had access to a 3D printer, I designed this part to...

These are rear bumper dome caps designed to fit the following truck models: Toyota Tacoma 05-15 Toyota Tundra 00-06 This is to replace Toyota part number PT22834000BK Note that I did kind of wing it on some of the dimensions, and they fit very...

These holders attach using the existing trim screws in the tailgate of a 3rd gen Tacoma. The base fits flush when tightened, and the screw head is recessed. I built them for trekking poles with a diameter of 18 mm. There are two versions of clamps,...

This part is designed to replace the 3rd gen Tacoma switch panel that's located next to the driver door.it can hold 7 rocker switches which can be found in the following link...

One of the few negatives of first gen Tacomas are their door handles which are known to crack. Some of the non-OEM handles are made out of a materiel that does not hold up in freezing temperatures. After snapping a handle this winter I decide to...

Blank switch inserts for the center console of a 2nd gen Toyota Tacoma (2005-2015) I designed this for my under-seat subwoofer install to have a clean bass volume adjustment knob. I have included STEP files to make it easier for you to customize your...

This replacement steering wheel emblem is specifically designed for the 3rd generation (2016+) Toyota Tacoma steering wheel, requiring the removal of the OEM chrome emblem to fit seamlessly. The holes at the back are carefully crafted for 1.75...

This iPhone 5 dock fits a 2009 Toyota Tacoma, replacing the passenger airbag switch and utilizing the Apple Lightning connector. Designed for an iPhone 5 with a slim case (similar to Elago S5), there's also an iPhone 4/4S version available. After...

This thing is a mounting adapter to mount KC Cyclone V2 LED lights under the hood of 2nd gen Toyota Tacoma. Adapters should be placed on either side of the sloped section of sheet metal along the front edge of the hood. These adapters will aim the...

Hi All, This is an adapter that lets you attach a NATIKA WD-011 camera available on Amazon to the factory backup camera location on a Gen2 Toyota Tacoma 2005-2015. I have a 2008 model that didn't come with the factory backup camera, so I got a Pop &...

This is a remix of this: https://www.thingiverse.com/thing:471614/files I increased the size to 120% of his and mirrored the vent part to add depth to fit nicer do to the Toyota Tacoma vent fins. Print his hose attachment at 120% and this hose...

I designed this to follow the lines of my 2013 Tacoma dash. It use the RAM mount ¼ ball system, along with my Quadlock case for my iPhone. I printed it out of PETG. You do have to remove the dash to epoxy the support plate behind it. I didn't want...

This thing is an adapter to enable you to connect up threaded Euro 45mm brake reservoir pressure bleeder cap to your Toyota Tacoma (and perhaps some other models) instead of having to use a mega cumbersome "universal" adapter. Use with a typical...

A friend of mine has a new Tacoma and asked to collaborate on a design to hold a couple of ammo cans on top of the fenders in the bed of his truck. He wanted a place to store some tools and ratchet straps and this seemed like a pretty elegant...

When installing an "add a fuse" accessory to the fuse box underneath the steering column of a 3rd gen Tacoma, it becomes impossible to fit the stock fuse cover back on without modification. This fuse box cover is designed to provide added clearance...

This thing is a pair of adapters to connect your brake power bleeder to the master cylinder of your Tacoma and some other Toyotas. These master cylinders have a press on rubber cap and the universal adapter that comes with the pressure bleeder is a...

This is a replica of my Gen2 Toyota Tacoma, scaled down to 1:32 for the Orlandoo Hunter line of RC trucks. The original design was created in Sketchup, but I heavily modified it using Tinkercad and Meshmixer afterwards. ... You can see the original...

This is a front oil axle seal driver designed specifically for a 1st generation Tacoma, with potential compatibility also extending to the 3rd gen 4 runners. The part number for this design is 90311-47027. Crafted based on the dimensions of the...