table and mitre saw combo 3d models

I purchased a feather board from Harbor Freight, but unfortunately, the rail guide was too wide to fit my Craftsman table saw. To solve this issue, I created an adapter that fits the rail width of approximately 15.5mm. When you tighten the knob, the...

The rear cover/brush holder for the motor on my Delta table saw was damaged and I really needed to replace it to make the saw safe again. Now you can too! Print Settings Printer Brand: Ultimaker Printer: Ultimaker 3 Rafts: No Supports: Yes...

... need to add the screws, washers, and nuts that hold everything in place. Don't forget to tighten them securely to ensure a safe and reliable experience when working with your table saw. ... Hope you all enjoy building this safety hand push block!

Guard for holding the blade on a 10 inch table saw when changing the blade. Could be useful protection even if your saw has an arbor lock. Fusion360 and STEP CAD files included. Printing is easy. Use a reasonable amount of infill. Remember to turn...

This design is a remix to adapt a featherboard to fit a DeWalt portable table saw. The main body is the 6 mm featherboard with no changes. The main body is larger than necessary with my DeWalt portable table saw. The 'MINI' is smaller and will...

Inserting a scroll saw table can be done by hand, but we'll outline it below so that anyone following along will have the proper guidance: 1.) Take the provided parts - in this case, part number 327415. Assemble them according to the provided manual...

It's nice to be able to print your own. This is designed to work with a 1/4-20 Hex Nut and 1/4-20 Hex Bolt (at least 1 ¼" length)The files included are intended to be used as an accessory to a push block for woodworking.The accessory is intended to...

A ZCI is used to provide a smooth, gap-free work surface on the saw without a space for narrow cut-off pieces to fall down in and possibly get wedged and thrown out. The insert is installed on the saw, then a board is clamped across the top. With...

... fillet on the surfaces that led to me printing with supports and then having to sanding it off. I'm not in love with how the surface finish turned out, but it lives under the table of the saw, in a basement, covered in dust, so choose your battles.

The slot on this tool must fit snugly onto the table saw's 20mm wide slot, so be prepared to sand it down until it fits perfectly on your machine. As you can see from the picture, we secured the wood piece in place with double-sided tape;...

I designed custom spacer blocks for my Ryobi Table Saw to bring it up to the desired height, allowing me to utilize my bench as an out-feed table since I elevated the top of the saw just slightly above the bench. When cutting a piece of wood, the...

... to execute. Simply tilt the table saw blade at a precise angle with a wedge-shaped insert placed inside, secure with some screws or even glue, cut your angled wood piece with ease and perfect precision. ...Easy as can be, try it yourself today.

Diagram showing the measurements of the runners, and the T-slot in the table saw bed are shown in the pictures. ... The runners protrude slightly above the level of the bed to allow the sled to move, so don't use these for featherboard locks (as they...

To assemble the railing to get a rail all the way across the table saw, gently trim the corners of the pegs on the ends with filament nippers, and it'll fit into the hole in the center rail with some elbow grease. ...For final assembly, put some CA glue...

A 3-in-1 cutting saw table is a versatile and innovative tool designed to provide users with the flexibility to perform multiple cutting tasks using a single, compact workstation. ...This type of tool typically combines three essential cutting...

My Powermatic Table Saw motor control had a STOP switch that was infuriatingly hard to locate and even harder to activate when I needed to shut off the saw instantly. Modern saws boast a spacious STOP switch that's readily accessible with either hand...

The saw runs like a top and with the exception of the Biesmeyer Fence and a junky little sheet metal motor cover it is all original equipment. Even the power cord (with a new plug). The saw weighs around 520lbs. They don't make tools like this...

This is a throat plate for the Rigid R4516 Table Saw. Tolerances are tight on this print and will likely need to be sanded slightly for a tight and secure fit. if using the two part due to your printer not being large enough to handle the single...

Dust hood for a Ulmia 1710 table saw to fit a Festool 35mm vacuum hose. Modeled quick and dirty, but gets the job done well... You need a m5/m6 screw to attach it to the blade guard and another m6 to set the depth. ... You could insert a nut to secure...

I lost a foot for the Craftsman job site table saw, so I took one off one of the others (Black) and modeled a new one (Red) from the original.The final print was printed with the remainder of my red and finished with black.

This poly model portrays a blacksmith table saw with accurately positioned pivots. All components are appropriately labeled, situated at genuine real-world scale, and anchored at real-world coordinates zero. ...The textures encompass diffuse, specular,...

I found it was too time consuming (and too tiring) to raise or lower the blade of my table saw by hand.So I created a tool that allows you to do this with a cordless drill or screwdriver.A real time saverThis is a table saw from the Parkside...

Proxxon FET Table Saw Vacuum Nozzle I made this nozzle to improve the dust extraction of the Proxxon FET table saw vacuum cleaner adapter. The opening of the suction attachment is located on the rear wall of the inner housing, but the saw blade...

First off is the miter rail with the arrow and holes already laid out for the miter gauge that comes with the saw - one solid option and another pre-drilled model. On my saw, these rails slide smoothly into place with no signs of wiggle. There's...

Spacer for a saw blade laser tableparts needed:M5 threaded rod4*M5 nutscheapest saw blades you can get (for my bed 24 pieces)46 spacerRebore the holes in the saw blades to 5mm, put them on threaded rods, place spacer between the saw blades and secure...

I've created a custom 10" Table Saw Belt Guard designed to replace the Craftsman Part #: 60252. The Fusion 360 archive file is included, featuring a parametric design that allows for easy customization. ...Key parameters such as Pulley Hole Diameter,...

This is an exact replica of the plastic clips originally attached to a Ridgid TS3650 Table saw fence. Due to their unavailability from the manufacturer, any damage or loss can render the fence unreliable. ...The following model has been printed using...

A customized locking mechanism designed for the Dewalt DW7491 table saw mirrors its factory-installed counterpart. ...Easily integrated into DIY throat plates, this device secures the throat plate firmly at the infeed point, ensuring a reliable and safe...

Summary Part for 1980s Rockwell table saw hand crank for raising and lowering blade. ... Original idea from: https://youtu.be/cDfMI5ahbJI Print Settings Printer brand: Creality Printer: Ender 2 V2 Rafts: No Supports: Yes ...

Track Slider for my table saw for feather boards and other accessories. The slider part is designed to take a M5 countersink bolt, I use 65 mm. ...The knob has provision for a M5 nut which I simply drive in during assembly with a hammer.