t4 2 team associated 3d models

This is a rear body post adapter allowing you to run a team associated Reflex 14T Truggy body on your 1:16 mini revo. On the lowest post setting this adapter and and body combo still clears the hot racing sway bar kit (front and rear) with the...

Team Losi RC10B 4.0 DTS 8SP Tqe1019\nTop-notch build. Factory-measured specs. ...\nAvailable in: IGS STEP STL OBJ 3DMF 2MPT 6PRN DWG DXF DWS CAD PDF FOD RXE

This is a customizable case for the Lilygo T4 2.4" microcontroller board.It's designed with FreeCad and you are welcome to modify to your own needs.All sizes are stored in spreadsheeds, so it's very easy to adjust them without going into the...

A layer height of .1 to .2 works well, but .1 is ideal for the best quality. PLA material works, but PLA+ performs much better. The V12 version has some slight modifications to prevent cracking in buggies, especially when used on carpet. ... I've...

Hello everyone, Replacement clip for Quechua T4.2 tent. Printed in PLA. Two models available with or without breakage. Good DIY and leave a LIKE!!! If you have questions about assembly, print parameters of these parts or other projects, feel free to...

If you like to design your own case for a T4 2,4", it's nice to have a model of your stack for reference. Here it is :) All metrics are available in the spreadsheet, so if you like to modify something you don't need to change the sketch. A case...

A custom battery bracket was constructed after the replacement battery's dimensions had grown wider.

I made this for my tc6 because the factory ones kept breaking

Front body mount bracket for the RC10T2. ... You may need to ream out the screw holes slightly, but 4-40 screws should thread in just fine.

Reproduction of the front bulkhead of the RC10 B2

Rear lower shock mount for the RC10T2. The holes for mounting the arm could be reamed larger to allow the screws to pass through more cleanly (if desired). ...The shock mounting holes should be tapped with a 4-40 tap.

If you're installing a receiver on the opposite side of the motor and you've taken off those protective guards, this is the bracket you need to mount your antenna. ...To get the best outcome, print with PLA at an infill of at least 50%.

You'll find a collection of useful parts for your AE B6.1 here. Note: STL references may print but often do not fit exactly. However, printable components have been printed and verified to be exact fits. Reference photos can be used in Fusion 360...

Modeled as accurately as I could measure.

I designed a custom case that's specifically tailored to fit a 48mm wide lithium-ion battery. ...Its purpose is to securely hold my lipo in place.

Side battery mount for the AE B6 series

I needed adapters to mount my B6 gearbox on my SC6.1 chassis for a no prep car, so I built the stack to be 8mm and the spacers to match. I replaced the rear gearbox brace with a taller part, and added a wheelie bar mount. Then I got greedy and did a...

I needed to bring my mounts forward for my bump box YouTube Channel https://www.youtube.com/channel/UCZ8WG-kqF1kmL2s0xIMfIIg If you found this video helpful or would like help fund future experiments.please donate below. ... Patreon ...

More squish = More tractionIf you have the TR28 wheels, you can use the Nanosport street tires since they are the same size.Make sure to chase with a 2mm drill bit.

Here is shock tower extension to help get your shocks vertical for better traction that fits over DR10 rear towers. ...You will need additional screws and hardware to attach.

Front mini bumper for the RC10T/RC10T2. This is designed similar to an OEM aftermarket bumper (RPM) that was available once upon a time. They are getting incredibly difficult to find on the web, and there are probably more durable options...

Avoids purchasing an entire transmission case just to replace one minor component.

The standard button head screws on the shock tower can cause the body to crack prematurely. Putting this little body mount on the shock tower helps prevent this. It's very strong and fits very nicely. You will need to replace the standard BHCS-M3x12...

Reverse engineering a new car, and this is my progress so far.

This is a versatile battery holder/servo post combination. I've based my design on period-correct servo measurements like the Futaba FP S-148. Modern servos will likely fit, but you may need to trim a small section from the side facing the servo to...

Probably best to print this out of TPU/TPE

Modeled as accurately as I could measure.

Buying a brand-new machine was quicker and less expensive, but not as cost-effective as upgrading the existing one. ...The Rhino file was also bundled with it.

This is a LiPo battery front stop to keep your battery from rear-ending your electronics. It will bolt on to the antenna/shock mount, see in the picture. Use a M3x4mm BHCS screw sth. ...in that range.

I designed this specifically to hold an antenna for my rc10.\r\n\r\nA threaded hole is provided at the bottom, accommodating a 4-40 X 3/8 flat head screw that will secure the holder in place. ...\r\n\r\nTwo additional holes on either side of the holder...