synology drive bay key 3d models

This is a replacement key specially made to open my loft hatch. ...I presume this to be a standard key for such trapdoors and it might be useful for others here.

This specialized key was designed specifically to unlock my loft entrance. ...Assuming it's the typical key used for such access points, it could potentially prove useful to others in similar situations.

this fits in place of 3 of the 5.25" CD or DVD drive bays, and fits nicely on my PC. This is modeled to be printed with zero supports, and will print fine. The only slight overhang is the clips, and they printed without issue. Modeled to be...

This is a 3.5" Antec-style drive bay cover modified to provide two USB 3.0 and one USB 3.1 Type C front ports. For the ports, I used: https://www.amazon.com/gp/product/B01KJPUI5W and https://www.amazon.com/gp/product/B0755DDD9B connected to the...

I'm replacing parts for my Synology NAS DS414. ... Applied models include the DS211+, DS212, DS212+, DS213, DS213+, DS214, DS214play, DS216, DS216+, DS216+II, DS412+, DS413, DS414, DS415play, DS415+, DS416, DS416play and DS916+.

I needed more airflow in my computer, and I was not using the 5.25" drive bay.This was designed to fit in the drive bay of the Silverstone GD09 computer case, however it's not too difficult to remix, or adapt to your own taste.FreeCAD model files are...

Thing enables users to mount a 3.5-inch device (such as an FDD - Floppy Disc Drive or Card Reader) into a standard 5.25-inch PC Drive Bay designed for mounting DVD-like devices. Print Settings: Printer: Prusa i3 Rafts: No Supports: No Infill: ...

This customizable M.2 PCB or 2.5" SSD to 3.5" Drive Bay Adapter can be tailored to match your hardware. Simply click on **Open in Customizer** * Using the Customizer, you can specify the dimensions of each slot or mix an M.2 slot with an SSD slot *...

TPU "socks" protect Synology DS215J from sticky rubber feets. Over time, original feet became extremely sticky, leaving black rubber marks on table surfaces and hands. No more dirty tables with new socks in place. The new TPU "socks" ensure a cleaner...

The Pi housing should fit easily into any standard 3.5" bay, leaving room for power and HDMI connections to plug in securely. ...Make sure the Raspberry Pi is properly fastened before assembling and if necessary, use a heat source to mold and compact...

The Synology MR2200ac boasts a WiFi button discreetly placed on its back panel. Engaging this button disables WiFi until you press it again, rendering it inoperable. Unfortunately, there's no software workaround available to disable this feature...

It does not do a great job in preventing the vibrations of the disk station from jumping over to the wall ## Vibration dampers The dampers are printed with PLA and decouple the disk station from the wall mount Edit 09.05.2022 Original damper might be...

Adapter for installing a thin DVD drive together with a 3.5" card reader into a 5.25" port. The drive mount was glued in place. ... Print options standard 0.2 infil 10-15% support no

Instructions Removing the original parts isn't hard at all: Just remove the 4 screws that hold the cartridge bay from the base and take out the whole piece (alternatively, you can remove the whole baseplate for more free working space before...

Please let me know if you encounter any issues. These M2 / SSD adapters make it possible to mount two M2 SSDs or two 2.5" SSDs in one 3.5" hard drive mounting bay. Please measure the height of your SSD before printing the dual SSD adapter as some...

This adds some security by clipping the rear of the board onto the drive.When you are ready to take the drive out for experimenting, just remove the IDE adapter board and slide the drive out!Print flat on its botton at .2mm layer height. ...preferably...

Pour accrocher un routeur WiFi Synology MR2200ac au mur.La ventilation par le bas et le passage des câbles restent assurés. Des ergots empêchent le routeur de basculer. ...Ces ergots permettent d'accrocher le MR2200ac au plafond s'il est possible d'y...

Getting Power to the drives can be achieved using a couple of these: 15 Pin SATA Male To 2 SATA Female Power Extension Y Splitter Cable Adapter Cable And SATA Serial ATA 15 Pin Male to 4 pin Female Molex Power Converter Adaptor Depending on your...

... ...I'm convinced it's still structurally solid, with tension focused on the mounting points and both drive and case, rather than the central beam. This design should print faster too. ... Thanks go out to usermod for coming up with the original idea!

To attach the brackets to each side of a 3.5" drive, simply use normal screws, then secure the bracket to a computer case with wood screws. I deliberately left out holes for those screws because securing locations can vary from case to case. ... The...

The M350 case usually comes with only one bracket for mounting 2.5" drives and if you want to install a second one you'll have to print or buy an extra one.I usually don't believe in supplying presliced files but I am including some as you need to...

Adapter tray designed to fit a 2.5" SSD or HDD into a standard 3.5" drive cage or caddy. Important note: holes are intentionally precision-cut tight, allowing you to easily tap them with standard screws if necessary. Successfully fits Lenovo, HP...

CAUTION: Synology's instructions for this router are woefully inadequate, failing to mention the keyhole slots underneath. Instead, they recommend simply placing it on a flat surface. A safety note cautions against tipping it over, but I'm willing...

Note that one end has a higher wall, so the drive will only fit properly over the lower wall end. This is a pair of 3.5 drive to 2.5 drive adapter designs. One uses a typical M3 nut (approx 5.3mm across the flats x 2.3 thick). The other is a simple...

POST-PRINTING Typical hole cleanup for clearance of M3 screws which attach 2.5 inch drive. In the tapped version cleanup and use an M3 tap if you have one. You can clean up the hole a bit an use an M3 screw to tap the hole, but be careful. If the...

CAUTION: Synology's instructions for this router say simply to place it on a flat surface and make no reference to the keyhole slots underneath. There is also a safety note, "Place the product right side up at all times." Possibly I'll have gone to...

This might not benefit everyone, but I attempted to fill an open slot in my PC's casing, originally designed for a floppy disk. ...The fit was precise and snug, so it might not be compatible for others.

Here is a PC-mounted adapter holder that lets you plug in your Nintendo Gamecube controller on your gaming machine.

Should fit 2 70mm fans, tested with Startech units and they fit fine. May require some mild cutting in the event of clearance problems. Would suggest printing face-down, with only supports in the center. ... And also scaling it down 10x.