syma x5c motor 3d models

I made this for my Syma X5C Pcb (Can fit other Quadcopter Pcbs Upto 34x35.5mm Size I have one more model for 8.5mm motors (Search "Syma 8.5mm") Print using 20-40% Infill, PLA will go. ... Add Rubber Bands to fix Pcb/ Battery

I made this for my Syma X5C Pcb (Can fit other Quadcopter Pcbs Upto 34x35.5mm Size I have one more model for 7mm motors (Search "Syma 7mm") Print using 20-40% Infill, PLA will go. ... Add Rubber Bands to fix Pcb/ Battery

This is propeller of SYMA X5C drone. ...There is no need to use screws.

The Syma X5C drone's motor system features four brushless motors that provide a smooth and quiet operation. A 720p HD camera captures stunning video footage while flying. The drone also has a built-in Wi-Fi module for live streaming and real-time...

Replacing damaged feet on your Syma X5C Quadcopter? You can get custom-made parts that match factory standards. ...Since they are crafted from ABS plastic, the replacement feet typically weigh around 3.6 grams.

This is a replacement battery cover / camera holder for the Syma X5C quadcopter. The key difference between this and the original one is the camera's orientation - it's now perfectly level, no longer pointing downward. ...I designed it to be simple to...

This compartment is specifically designed for safely storing the battery of your Syma X5C drone. Additionally, it features a designated space for conveniently holding the battery charger. ...To customize the design and increase the number of battery...

Pontoons for a Syma X5C Quadcopter. I have no Idea if these will actually work. I'm thinking that you should have several shells and very little infill (none, if you can get away with it.). I've dropped my x5c in the water a time or two, and the...

Pontoons for my Syma X5C Quadcopter are being considered. The effectiveness of these pontoons is uncertain. A high percentage of shells and minimal infill (none if possible) seem like a good idea. My experience with dropping the x5c in the water has...

This Drone Frame is specifically crafted for the Syma x5c and also for other Syma categories. It's an Acrylic Frame that stands at a thickness of 2mm. You can download this file and send it to a laser cutting service in SVG format. To stay updated on...

I am putting an antenna on my Syma X5C drone. To get better range, I put a custom 2.4GHz wire antenna into the controller of my drone. After connecting the wire to the circuit board with some solder, I pass it through this housing and click it into...

The downside is that the X5C can't lift much, so with the larger battery, it can't recover from an altitude drop. Need to figure out a way to boost the thrust. Anyways, hope this helps someone. ... Print Settings: Printer: Geeetech Rafts: No Supports:...

These are the files I created to convert my Syma X5C to use brushless motors. The entire build process is described here. https://j2n.nl/blog/anchor-cms/index.php/posts/x5c-brushless-conversion The conversion boils down to removing everything until...

Different parts to install a camera on a Syma X5C drone. There are two different feet for the drone, as there are two different sizes at the end of them. The bumpers are printed in flexible material and held with screw collars. In my case, the...

I stumbled upon an amazing drone design for the Syma X5C on Thingiverse (https://www.thingiverse.com/thing:1531770), but after assembling all parts, I felt unsatisfied with the result and decided to give it a complete redesign. My new design is...

I came across this great race drone design for the Syma X5C https://www.thingiverse.com/thing:1531770 but wasn´t satisfied after mounting all parts together so I decided to do a bit redesign. My design is much lighter and also have a camera...

Portable Power Station with Rechargeable Battery Case and Micro USB Charger for Syma X5C Quadcopter Drone

This is a basic square plate designed specifically for mounting a Quanum Pico or other tiny brushed-motor flight controllers onto a Syma X5C drone. ...To install it, you need to remove the existing flight controller from the X5C first and then attach...

After mine broke, I decided to keep the frame and replace the internals with: -SP f3 flight controller -FS-ia6b receiver -80A PDB with 5v and 12v BEC -20A BL Heli_S ESCs -All-in-one 5.8gHz 600tvl FPV camera -RX1803 2500kv brushless motors -4x4.5 DAL...

The casing itself requires no additional connectors, boasting a slightly heavier weight than the original Syma X5C casing. A camera mount is not integrated, but can be conveniently secured to the flat underside via either duct tape or adhesive Velcro...

This is a revision of SYMA X5C WALL HOOK by dionlevi, optimized for printing without support material as one complete piece. The design boasts increased strength and simplicity in mounting while providing ample space for all components. I chose to...

This is an FPV AIO camera mount for a brushless 3S Syma X5C. It's meant to be strapped securely on top of the canopy, providing a stable platform for flying FPV. The mount features a hole for the battery strap to slip through, ensuring a snug fit and...

... millimeters. On the four mini squares holding the Syma receiver board, there are holes that keep it in place. Due to resolution differences, these holes might not be perfectly made. ...You can adjust the hole diameter according to your screw needs.

Designed these custom legs to replace the standard ones from Syma, providing a seamless upgrade to your quadcopter's performance. For optimal printing results, consider using support structures for the knobs that insert into the main body, as this...

The X5C camera should also have sufficient clearance. Print Settings: Printer Brand: Printer: RepRap Supports: Yes Resolution: 0.2 Infill: 30 Notes: To print these lightweight legs successfully, set your infill to 30% and select a two-perimeter...

I hacked apart CabriDIY's GoPro leg design, yanking off the connectors to repurpose them as a makeshift attachment point for a pyramid-shaped spike. The goal was to mimic the innovative setup used by modelsport with their DJI Spark floats...

Human-Modified Version of Thingiverse Model #58849 Generated Using Customizer Tool http://www.thingiverse.com/apps/customizer/run?thing_id=58849 Using Preselected Settings: * Width: Expanded to 9 Units * Height:...

One side of the helicopter wouldn't accommodate all the equipment. ...To make everything fit, I modified the setup to use both sides of the chopper.

Please consider a Simple Wall Hook for Boys and Girls - I'd greatly appreciate it if you could provide that information in print form, and then let me know.

The FPV kit can be found at www.banggood.com/Syma-X5C-1-X5SC-Real-Time-Transmission-Monitor. For the best results, print with 100% fill. It comes equipped with four M3 x 12MM bolts and nuts that attach to the remote. Attach it with a #4x3/4" self...