swivel socket holder 3d models

                                               ...

The AA battery holder works nicely even if not using it for this project and is designed for flexibility when runnning wires and connecting them, as well as what you want to use as battery posts. The lift system is still a bit crude. I won't be...

                                               ...

Print the light bar and 3 of the nut holders. (Steps 1 & 2 from the non-switched version) 3. Clip the ends of the mini rocker switch so they fit inside the enclosure once it is inserted. 4. Loosely place the LED strip and switch where they will go...

They have a screw hole in the back to fasten to a wall and the the sensor just sits in the holder, allowing easy removal for battery replacement. I can also print and position several mounts and it makes it easy to place the sensor in different...

 Printing instructionsBox: Filament: PET-G (We use Prusament PETG Orange and Prusament PETG Recycled), Infill: 100%, Perimeters: 3, Layer Height: 0.2mmOther 3D printed items: Filament: PLA, Infill: 100%, Perimeters: 2, Layer Height: 0.2mmGame board:...

Axle parts: Housing 5mm Bearing holder Housing backing Frame parts: Frame parts are able to rotate to fit together. There is the ability to add 2mm steel rods through out where they join. Length range 40mm to 100mm. 40mm are the holes that line up...

With a filling in the order of 20% they occupied me 1.4 - 1.7 kg of PLA +.The spindle holder is designed for a 52mm diameter Chinese mini lathe (cheaply available at hardware stores and tool shops).Both nema 17 and nema 23 motors can be used.As a...

Print profile is in the attached 3MF file and Gcodes, which are for a CR-10 upgraded with a BTT SKR Mini E3 V1.3 with MicroSwiss DD extruder and dual Z stepper using Klipper. Build instructionsSwitch off and unplug your printer just to be...

They each had pros and cons. Spool holders and buffer that came with the MMU2(s): Worked well enough but they took up a TON of room (Like an entire dinning room table of space). The spools needed to be placed behind the printer and in line to...

It fits my battery holder very nicely, and I drilled two small holes to run the wires down into the body (hence the small notch in one side). I did a layer change at the top so that I could print the "exhaust pipes" in silver. I found them here:...

Headlight + handle req: ABS filament to print holder, 2 flashlights, 2 Samsung 18650 batteries, 2 M4 screw + nut (15mm long approx.), flexible orange band for handle. I don’t think it’s a big deal, but it would be if the flashlight was any closer. I...

... Also check out my other designs. The tags fit really well with the following designs: Rain Gauge:Colorful Wind Wheel:Also, inspired by the the tagging system, I created a new design for indoor use, you might be interested in:Slide-in Label Holders:

Use (2) heat inserted knurled nuts at the back of the Carriage top and mount the Carriage PCB holder into these knurled nuts. 10. Slide the X linear rods into the linear bearings now mounted to the Carriage assembly. 11. Install all the...

The Tray: (Optional) Print the desiccant pack holder, “Drybox Desiccant Tray.stl” (Recommended line width, 0.5mm). You could also skip the tray and just add desiccant packs to the empty basin at the bottom of the base too. If adding loose desiccant...

- PINDA Adjustment & Positioning Tool(Achieve the perfect SUPERPINDA position)MMU2S Single Filament Guide Festo M5 Coupler(Retain your original MK3S spool mounting while still using MMU2S in single color mode)Nozzle Holder Case Ultra(Biggest and...

To complete the connection system you will also need (Included):- MDS_TRACK_CLIP_Standard (To connect track parts)- MDS_TRACK_CLIP_Pianos (To interconnect pianos)- MDS_TRACK_CLIP_Lanes (To fix straight lanes in parallel)- MDS_TRACK_CLIP_IR-holder...

The center handle locks in and keeps the lid closed, avoiding putting any stress on the hinge to do so.UpdatesUpdated my model to keep the same spacing but different grip sizing so that different pens/pencils can be accommodated for four and five pen...

Use (2) heat inserted knurled nuts at the back of the Carriage top and mount the Carriage PCB holder into these knurled nuts. Slide the X linear rods into the linear bearings now mounted to the Carriage assembly. Install all the original parts into...

Im starting here with version V2 (V1 is only in one picture; there was too much wrong with that), which will come in 2 iterations/stages: ++++++++ Stage 1: ++++++++ - changing out the Heatbed to a 150x230mm 12V PCB...

There weren't enough space in the original Hercules carriage for a dial indicator holder so I decided to make this separate carriage for a dial indicator.The Hercules carriage is very easy to remove. Just unscrew the parts cooling fan duct from below...

I have shortened the magic band reader holder post to be more to scale with the rest. I as well added a half inch hole through the post and the plug to be able to past wires between the electronics without drilling, half inch might be oversized but...

 * **There is no defined end-stop mount on this design yet** Unfortunately, with all the different belt holders, bearing setups and hotends people use on the A8, I can't really come up with an endstop system that...

Make sure they understand you want a ring and the star, or you might get a negative (I sent the green picture along to make it clear - the DXF only contains lines, so it's hard to tell). Added mounting holes: I used two old leather belts to make...

TL;DR first: Welcome to my Overhaul of the Creality Ender 2! Im starting here with version V2 (V1 is only in one picture; there was too much wrong with that), which comes in 2 iterations/stages: ++++++++ Stage 1: ++++++++ changing out the Heatbed to...

2 other holes with M3 thread inside are needed for front-left and rear-right glass holders. Bed plate already has similar holes in 2 other corners (see image). Print 4 copies of corner.stl thing. ABS would be the preferred option. Use 0.2mm...

You will need to remount the extruder up top by the spool holder or swap to a direct drive. The stock motor cable should be long enough to reach (at least on my machine). I don't have the dimensions for the Anycubic Mega Zero V2 but as long as the...

- Install the speakers - Route all cables - Cut covers for the speakers (Mine are made out of 1.5mm perforated stainless steel) - Screw the covers and the "Bumper holders" to the base - Slide the bumpers on that, If you want to make sure nothing...

If you have access to a 3D printer, it would be best to pre-print some of the parts in the download, in particular the BLTouch holder and extender plinths. The BLTouch v3.1 probe (raised using M280 P0 S10 in GCode terminal) will need to be set at...

It is a remix of the original spoolholder that uses printed roller arms and springs to press the spool down.To improve the stability of the arm, the profile was divided into two halves, the lower one containing the bushing and separated by a gap of...