swiss micro 3d models

This is an interface plate created for the Micro Swiss NG for use with the Wham Bam MUTANT V2. printed at 0.2 layer height. You will need 5 x 3 mm threaded inserts that come with the MUTANT kit Two versions available. Version A: ...

I used the KentoHardRok adapter to perform my Micro Swiss direct-drive upgrade to my CR10S Pro v1 and found that that both mounts for the BLTouch referenced from the remixed design exceeded the sensor offset limits on the firmware used. I modeled a...

The Micro Swiss hotend performs perfectly, whereas myself and others I know have encountered numerous issues with the Monoprice factory hotend. No new hardware is required. Simply print the backplate with supports oriented upwards, while the...

Nuts have inset spaces where they can be press-fit, or if resin printed, locked in with some cyanoacrylate glue or resin set with a UV light.Two variants of the Fan Block exist - one for a 4010 fan, and one for a 4020 noctua or similar.The mounting...

Micro Swiss Direct Drive Extruder Only (part #M2602) or Micro Swiss Direct Drive Extruder and Hot End (part #M2601) Offset for my extruder: X= -46.00 Y= -9.00 Z= -1.75 to -1.90 (set to -1.65 for the initial till you can find your Z Offset) Fits...

I installed this on a customized Longer LK4 Pro (sort of an Ender 3 clone), hence it should fit any Ender 3 version that has been modified with a Micro-Swiss Direct Drive extruder, and probably other printers as well. I used standard 40x40mm...

I installed this on a customized Longer LK4 Pro (sort of an Ender 3 clone), hence it should fit any Ender 3 version that has been modified with a Micro-Swiss Direct Drive extruder, and probably other printers as well. I used standard 40x40mm...

The Micro Swiss manual states that the cold end should protrude 1.7mm, so I've made the MK2 1.7mm available with or without support. I've downloaded and tested a few of these drive plates, but none of them worked for me. I'm printing with the...

This is a remix of a remix of the fan duct, that will fit better (not perfect) if you have a micro swiss hot end installed. I'm not an expert (first remix) i took the existing model, i've put it in fusion 360, cut it in half and added 3mm on the Z...

[UPDATE: January 29, 2021] I remodelled the x-axis cover part so that the endstop cable is not squeezed between endstop housing and strain relief This is a re-mix of the cable management for Micro Swiss DD from FastIndy...

After installing my Micro Swiss NG I noticed the wires to the heater and thermistor moved while printing. I was concerned they would eventually break. I found redpiyaya's cable support but didn't want to have to remove the V-slot wheels to...

I traced the Micro Swiss linear rail bracket from a photo after performing perspective correction on it, and it should be the correct measurements to make this work. The MS Linear Rail kit is quite a bit wider than the roller kit, or stock...

I installed the Micro Swiss All Metal Hotend on my Ender 3 and initially encountered issues when I hastily assembled the fan duct. A sudden shock jolted me awake in bed, prompting me to revisit the Gabriel3DCaster design that I'm grateful for. To...

This has been remixed for better fit with the Micro Swiss Direct Drive. The chimney has moved left, along with a bit of cable managing on the back. v1.1: 1. Errors in manifold have been fixed which would cause holes and gaps between layers when...

The one that he made works with the stock Ender 5, but recently I upgraded to a Micro Swiss direct drive extruder. The mount that he designed hits the spot where the belt is attached to the carriage plate. The mount doesn't hit the belt clip now...

Fan shroud for the Micro Swiss NG Extruder for CR-10 V2 and CR-10 V3. SKU: M3206 Cooling Fan (Hotend): 4010 Cooling Fan (Part-Cooling): 5015 This fan shroud does not get in the way or affect of the normal CR-10 V2 / V3 probe mounts. The...

Designed to use with Micro Swiss Direct Drive Base for Ender 5. As a bonus - now it is so easy to operate extruder's spring arm. Screwed to the base using 2x m3x12 screws Needed to attach a 3/4 inch [split wire loom...

This is from https://www.thingiverse.com/thing:4975364 using the micro swiss all metal SE for the Flsun Q5 mod https://www.thingiverse.com/thing:4920704. Added V2: with better air flow and lowered even more. Added V3: moved the duct back more...

Micro Swiss Direct Drive Extruder Only (part #M2602) or Micro Swiss Direct Drive Extruder and Hot End (part #M2601) Offset for my extruder: X= -48.5 Y= -8.5 Z= -1.75 to -2.10(set to -1.65 for the initial till you can find your Z Offset) Fits CR-10...

2 Adjusted Screw Hole Alignment, Added support wedges REV.1 Adjusted Thickness of clamp face and screw holes Files: -Custom_Nova_5015_Mount_Ezabl_Final_RTP -Clamp_For_Nova_Hotend This is A Custom mount to attach The Nova hotend to a Micro Swiss...

Upgrading to the micro Swiss direct drive kit for the Ender 3? This extruder knob reclaims the original brass extruder gear as its core component. I grew weary of extruder knobs relying solely on plastic contact points, which can be easily rounded...

The stock BL Touch mount integrates seamlessly with the Micro Swiss direct plate, but be aware that removing the fan cover for any reason necessitates a check of your z-offset since they utilize identical screws. The MS mount boasts two unused...

It was modified to fit with a Micro-Swiss dual gear direct extruder with hotend kit. I used some red silicon ptv to help seal it to the machined base. I didn't think I needed to drill and tap an additional hole. The h5 fans seem to be holding...

This is a hastily crafted adaptation of the hero me gen 2 tailored specifically for the mosquito hot end to be paired with a micro swiss direct drive extruder. Being entirely new to design, I relied on tinker cad to customize Mediaman's original...

*Note:* This fan duct has been designed for the Ender 5 Micro Swiss direct drive hot end. I don't know if it can be used on any other model. #Description This is a remix of JeffrayMK Satsana dual 5012 fan duct...

It's possible that all I needed to do was raise the temperature or change some settings, but I bought a Micro Swiss hot end, found it to be 5.3 mm too short, modified the part that this design is based on and have since gone through several rolls of...

DEPRECATED DESIGN Please be aware I am not developing this design any further. This is v2, an upgrade I think to the previous version. Made of 5 parts that are much easier to print. Screw them together with M2.5x10mm Socket Head screws. Designed...

This is the Hero Me Gen4 base for the Micro Swiss direct drive extruder, as modded by Marcelofs13, with one key adjustment made. The location of a critical screw has been shifted to prevent sagging on the right side of the base due to high...

So I got my Micro Swiss direct drive and hot end upgrade but didn't like the cooler shroud that needed to be printed as it utilizes the single 40-10 part cooler fan. I wanted to increase my part cooling so i bought another 40-10 cooling fan and...

The Micro Swiss end was initially set up for the original drag chain's end mount, while the bottom rail mount was designed for the new chain end. If you prefer both chains to use the same mounting type, you'll need to modify the Micro Swiss end to...