swiss micro 3d models

Micro Swiss Linear Rail Direct Drive - BLTOUCH Mount

two variants of hotend cooling for micro swiss hotend for CR10 and similar

a quick and simple hotend wire strain relief for the micro swiss ng

Micro Swiss themed 40mm fan guard. ... If you are looking for the entire fan shroud and part cooling fan duct for the Micro Swiss direct drive kit, see here: https://www.thingiverse.com/thing:4934569

Shifted a bit to each side to make room for the Micro Swiss extruder instead of stock

Designed to fit Micro Swiss Direct Drive and allow you to secure your BLTouch to the aluminum frame

Satsana for the Micro Swiss Direct Drive with a BLTouch on the Ender 3 doesnt matter what model and whatever other models the Micro Swiss Direct Drive fits. ... I redid this Mini because the Swiss Hot End loves this Satsana, the fan blows onto the...

The modified base was specifically designed to accommodate the micro Swiss direct drive, which has a slightly greater thickness than the standard mounting plate found on Creatliy printers.

Micro Swiss all metal hotend mount for Prusa mini. ... Requirements: 2x M3 inserts to mount the fan 1x insert to mount pinda Various M3 nuts and bolts

Couldn't find a good way to make the cables look clean after installing a Micro Swiss direct drive on my ender 3v2 so I made this.

This is the extruder knob Micro Swiss suggest you use in there manual made by ReplayMD on Thingiverse. ...https://www.thingiverse.com/thing:2776404 I remade it to fit the Satsana fan shroud for the Micro Swiss Direct Drive that I extended.

... instructions to install the DDX. Bondtech DDX https://www.bondtech.se/en/product/bondtech-ddx-for-creality-ender-cr-10s/ Micro Swiss Hotend https://store.micro-swiss.com/collections/all-metal-hotend-kits/products/all-metal-hotend-kit-for-cr-10

Simpler Knauf for Micro Swiss Direct Extruder with Direction Indication, since this works in reverse to the normal Extruder. ...Printed with the following Settings: Layer Height 0.12mm Filling Lines 20% Material PETG Gray (Amazon)

This remix supports the Minv2 Fan Mount installed on the Micro Swiss Direct Drive kit with precision engineering. ... The clearance between the blower fan and extruder motor is snugly tight, yet operates seamlessly without a hitch.

Direct drive extruder adapter remixed for use with a Micro-Swiss extruder. Print laying flat on its back with support. ...I would recommend 100% infill on at least the screw part.

mod for micro swiss ng for the voxelab aquila estop. my stepper motor was in the way of getting to the estop. It attaches to the bltouch holes. ...I used the screws from the stock extruder.

This mount has been designed to allow the Micro Swiss / CR10 hotend to attach to the Tevo Tarantula, it also supports the SN04 Sensor. ...This is designed to take 3mm brass inserts where the hot end would mount

This cooling case works with an 4010 fan. ...Connect the fan with the hotend fan. Print it with support and support blocker. I printed it with PETG. Works fine. Temperature Micro Swiss Extruder is constant 32 degrees. ...

This is a guide/support tower that screws into a convenient, unused and tapped hole in the Micro Swiss Direct Drive carriage plate for the Ender 5. ... **You Will Need** - 1x M3-12mm screw and M3 nut - 2x zip ties

This is a part cooling duct for 40X10 or 40x20 fans designed to be mounted to Rimba's Hot End cooling duct for the Micro Swiss direct drive kit on the Creality Ender 3 and compatible printers: https://www.thingiverse.com/thing:3808538 This duct will...

These are the 3 set ups: 1 - Micro Swiss Direct Drive and Stock Hotend 2 - Micro Swiss Direct Drive and Dragonfly BMS Hotend 3 - Micro Swiss Direct Drive and Dragonfly BMS Hotend W/ dual 4010 blowers Note: When mounting the BL Touch, the top...

Custom Fit Extruder Knob for Micro Swiss Bowden Extruder The knobs provided by Micro Swiss were all too loose, so I created a simple OpenSCAD file to generate a custom fit knob. Customizer parameters: - id: Inside Diameter - The inside...

This is my attempt of making a direct drive mount for a Micro Swiss hotend, most of the assembly is printed in PLA but the Micro Swiss mount is printed in PETG. The belt tensioner is a modified version of the piece made by...

This is a remix of the Micro-Swiss model which retains all of the critical geometry, but greatly simplifies the model by removing the fillets. ...This is meant to serve as a starting point for further customization without having to deal with the...

You need a Micro Swiss clone for your Creality CR10s Pro. ...To assemble it, you'll require the following parts: * 2 x M3 x 20 screws * 4 x M3 x 14-16 screws (for Fan 1) * 1 x M3 x 16-18 screw (for Fan 2 above) * 1 x M3 x 20-23 screw (for Fan 2 below) ...

This is a remix of the Micro-Swiss model which retains all of the critical geometry, but greatly simplifies the model by removing the fillets. This is meant to serve as a starting point for further customization without having to deal with the...

Quick tweak of this handy knob to free up the extruder lever on the Micro Swiss Direct Drive Kit. Step file available. Modifications: Trimmed down the shaft to give the clamping lever plenty of clearance. ...Smoothed out the shaft's taper for a more...

This is a little kit I designed to store spare parts for my Micro Swiss hotend.Parts stored: Heat break, Heat Sink/parts, and NozzlesI use 0.6 and 0.4 so I have those labeled.I've been using this kit to know when/if I need to re-order something.

Micro Swiss NG Dual 5015 Fan Shroud with CR Touch Mount.This is a work in progress, I have not printed this myself yet as I don't have 2 5015 fans to test with, yetOffsets for probe to nozzleX 93.2mmY 6.8mm

BL Touch bracket for Ender 6 with Micro Swiss NG direct drive extruder. Clears printer belt brackets. Uses M3 screws and nuts. Probe offset: M851 X-48.00 Y15.00 Z-4.10 Credit to DevDav I used his back plate to build off of.