swiss micro 3d models

Moved the 3d touch/BL touch out 5mm so you can fit other way round

This adaptor fits between the Microswiss and the Bigtree tech runout sensor

R18 10x15mm drag chain mount for wire routing.

The original fan shroud causes a loss of X travel on left and right side that I couldn't live with. So I narrowed it, moving the Pinda probe mount inside the fan shroud. The Pinda probe will screw into the hole allowing you to make fine...

I noticed that this design had not been properly adapted to the CR Touch without anything extra added onto the design and decided this would be very useful considering the benefits of the CR Touch compared to the BL Touch. The probe offset should...

Just dropping this off for now, I'll get back to adding BOM as soon as possible. These brackets enable the use of a Bondtech BMG extruder (use the Mirrored version) on the Mamorubot SX-4 CORE XY machine. One of the brackets also converts the front...

this hotend block replaces the original block. Thanks to the larger front fan, it greatly improves the cooling of the hotend, allowing you to obtain quality prints and extend the life of the hotend. Thanks to the excellent cooling of the extruder it...

UPDATE 1/26/2018 ************** I'm ending support for this fan due to a far superior duct system I've designed. Check out the details below. I had problems with airflow direction from this fan, which was pointing downward into the print more than...

So I've been using the original for a while now and decided it needed some improvements as well as some changes to suit my additional parts. Changes/additions are as follows all other parts remain the same as the original. Hope you all enjoy it. ...

I wanted to use this for my printer but did not want to cut and rewire everything. So this is a remix of the link with a removable clip harkening back to johnniewhiskey's design. For the other three pieces, I didn't bother remixing and just printed...

I didn't like the BLTouch bracket I got with the NG as I felt the BLTouch tip was too low during printing. One print that went a bit weird and overextruded actually broke my probe! ... Adjusted it to raise the BLTouch probe tip by 1mm, so the Z offset...

bei den 2 Bohrungen kommen noch 2 Gewindeeinsätze M3 rein, damit es dann auch verschraubbar ist. Infill hab ich mal auf 50% gesetzt damit die Gewindeeinsätze auch gut halten, das ganze wird dann mit dem ExtruderFan mitangeschraubt. ... PLA 0,2Layer ...

MicroSwiss Direct Drive Cooler (duel fan part cooling) With BL Touch For Ender 3 V2. This is a slightly modified version of my other cooler that now includes the mount for the BL Touch. This was included after some feedback asking for it to be...

Extruder visualizer for assisting in cleaning out the extruder tip.(I unplug the extruder and use this wheel to feed and extract the filament.)This fits the 5mm shaft with the flat spot, if printed correctly will press onto the shaft.I print it with...

I took kalrog2's idea and redesigned the modular 5015 blower adapter from scratch to be a bit more robust and optimize the airflow a bit while keeping all four screwholes usable for fixing the blower to the shroud. This is already updated to v2...

This is a remix of the "cable chain end" extruder clip by sebho85 - I corrected the position of the cable chain connector on the extruder clip because the whole cable chain was not properly aligned and therefore is twisted a bit. This twist can lead...

Created cutout for CRTouch. Original remix only worked with BLtoch. ...This will fit both.

I didn't want to lengthen any cables so I borrowed from Eric's design and added a few bits of my own. It works well. ... PS: This was installed on an ender 3 v2 which has different cable routing than an ender 3.

Just minor change for excellent Remix by PuDDeX. Added hole for screw that was behind duct as it was problematic to be mounted from side. During mound it is recommended to remove 4010 fan. Use M3 inserts for easy maintenance of fan (cleaning,...

I ran the print multiple times and successfully cracked the brittle filament with a well-placed strike from the filament cleaner. To strengthen the vulnerable section, I added strategically placed support in Tinkercad, ensuring it would withstand the...

<img src="http://nebula.wsimg.com/01c37ede5107382dac843255bf1665fe?AccessKeyId=D78877820DACAFA338E2&disposition=0&alloworigin=1" width="600" height="100"> <font size="2" color=brown>http://www.petsfang.com/</font> ***** ***** Use the...

When installing a new extruder, it's essential to consider how your printer defines its print space in the firmware. My CR-10 didn't allow me to make this adjustment, which resulted in the nozzle printing mid-air unless I tweaked my Marlin settings...

I used the original remix of [Akanar](https://www.thingiverse.com/akanar/designs) for a while. It fits really good :) Like often there is a "but". Akanar designed the remix for Microswiss DirectDrive "first version / generation". Thanks to...

Hobbled together something that will work to properly allow the NG extruder to hit the X-Axis limit switch on the Ender 3 V2 Neo from Creality. ...The switch style is that of the Ender 3 S-1 model which lays flat instead of vertical.

This is remixed to an have an 18mm z axis cable chain so that the rasberry pi cam cable can be fed through the arm and down to the chain to the control enclosure.

I needed a duct and didn't like the bulkiness of the ones available so i made one a little more compact. ... Its definitely still a work in progress.

Microswiss All Metal Hotend Adapter for CR10 V2 You can use the PETSFANG duct from https://www.thingiverse.com/thing:2759439 Let's Collaborate to Create an Even Better Design! I'd love to hear your ideas and suggestions! ...What improvements would you...

Removed some extra material that was preventing the clip from properly sitting on the stepper motor. Since the motor has differing dimensions for the black vs silver sections, the original did not fit quite right. I also removed a portion of what...

a low profile twist on this minimal knob