swiss micro 3d models

When using Micro Swiss Direct Drive the hotend needs to stay where it is so I combined the base with the gantry adapter similar to what was done with the model I'm remixing, but here I have included the BLTouch mount. This is also done in a way so I...

This is a remix of https://www.thingiverse.com/thing:4683505 The Micro Swiss Direct Drive Extruder changes the location of the mouth of the filament tube, so this model changes the position of the filament pulley. A 608 (skateboard) bearing is...

I was using https://www.thingiverse.com/thing:4742800 with stock ender 3 v2 but upgraded to Micro Swiss direct-drive and hot-end. I wanted to reuse the endoscope holder I had already and just mount it to this fan shroud. ... This endoscope is hooked...

my remix of the micro swiss NG shroud for use with a 5015 blower fan. Should be compatible with CR10, CR10s, CR10s Pro or similar with a 5015 fan. ... Hardware required: 2 x M3 nuts 2 x M3 20mm screws 2 x M3 washers Fully tested, updated to remove...

Fan shroud and probe brackets for the Micro Swiss NG Extruder for CR-10/Ender-3. Use support from build-plate only. Print using PETG filament or something even more heat resistant. The probe brackets attach to the NG main body using...

Hotend cooling system for Micro Swiss direct drive extruder for Creality CR-10 / Ender 3 printers. Design inspired by well known [Petsfang duct](https://www.thingiverse.com/thing:2759439). This one is less bulky and quite lighter (approx. 17g. ... ...

Modified to work better with 20mm thick fans, thermistors with nuts, Micro-Swiss Direct Drive, and the Creality metal BLTouch bracket. Closes up gaps and adds plenty of room for wiring. This also fixes the positioning of the stock part cooling fan...

This is a re-designed bracket to utilize Micro Swiss' Direct Drive extruder configured for linear rail. Additionally - I designed a cable relief bracket to help with cable management. Be careful with the mounting hardware - bolt length should be...

This is a printed adapter to mount the Micro Swiss Direct Drive Extruder for Ender 5 on a MGN12h linear rail carriage that utilizes the stock beltsIf you are looking for an adapter using CoreXY belt config, check...

Functionally, it straightens out the bowden tube as it enters the cooling block, and strengthens the connection to prevent excessive wear on the weak Micro Swiss bowden collar. Rationale: The bowden collets that come with the Micro Swiss all-metal...

Smooth Fang Mounting Plate - Ender 5 Plus - Micro Swiss Direct Drive - BLTouch - ExoSlide BLTouch Approximate Offsets = X-44.6, Y-6.6 Ender 5 Plus (with BLTouch probe), using a Micro Swiss Direct Drive extruder kit, mounted to an ExoSlide linear...

It uses an extra hole that the Micro Swiss carriage comes with making attachment more secure with three screws rather than two and no slots for to reduce movement. The BL attachment should not need any shimming and should be ready to go as soon as it...

The top hole is large and is designed for the press-fit, plastic bowden tube clip that comes with the [Micro Swiss Direct Drive upgrade](https://store.micro-swiss.com/products/micro-swiss-direct-drive-extruder-for-creality-ender-5), but will...

TLDR: This design accommodates the Micro Swiss block, reinforces arms holding the 5015 fan, supports gantry mounting point, redirects cooling fan for improved cooling, and features a cutout for heat brake set screw access. Print from materials like...

This is a printed adapter to mount the Micro Swiss Direct Drive Extruder for Ender 5 on a MGN12h linear rail carriage that utilizes the CoreXY belt configuration on the Mercury One.1, Voron 2.4r2 and maybe othersIf you are looking for an adapter...

5015 blower adapter for Micro Swiss NG™ fan shroud by Meister-D https://www.thingiverse.com/thing:6099380 Turbine style 40mm fan guard by Flintlocke https://www.thingiverse.com/thing:2505568 5.5mm lens Endoscope Inspection Camera 1-2M Soft Cable Led...

This is a StealthySwiss modification that fits the ExoSlide mounting system plate by Micro Swiss. The original StealthySwiss does not have a compatible mounting plate for the ExoSlide system, either in the listing or in the remixes. NOTE: My...

Which this part attaches This is for a Micro Swiss Linear rail Direct Drive (ender and CR series), where the Drag Chain goes left then under the motor. Any Material will do as long as the material will bridge easily with no support. One slot to mount...

The answer is yes, if you use Micro Swiss' direct extruder along with the cable strain relief from Sergentchat https://www.thingiverse.com/thing:4591387 (scale it down to 10 %). Then you will need a long shaft, to avoid collision with the strain...

Since I'm using a Micro Swiss direct drive extruder, I think I have more room between the X rail and part cooler, so it's possible to squeeze the bltouch in behind the cooling duct. ... These things are under the fans:...

I needed a better guide and also wanted to utilize the Micro Swiss adapter for their dual extruder. This new guide brings the wheel below the filament sensor, and sticks out a little further than the original design. ...This ensures that filament is...

Fan shroud and probe brackets specifically for the M3302 Micro Swiss NG REVO Extruder for Ender 5, Ender 5 Pro and Ender 5 Plus. Verify that you have the M3302 NG Extruder model number before printing out any of these parts. When printing the...

From my remix https://www.thingiverse.com/thing:5393935 of the original Micro swiss NG Shroud https://www.thingiverse.com/thing:5358828, I re- adapted the design to add a 50x7mm COB LED Strip Chip On Board. It is possible to cut and sand the strip...

I tried looking for parts to add a 10x20mm cable chain to my Ender 5 Pro with a Micro Swiss Direct Drive Extruder with the Exoslide Linear Slide Kit. Here is the 10x20mm Cable Chain I used, https://a.co/d/iSzwFDn There are little rectangular...

This spacer/bracket is to move the filament sensor so that it can be used with the Micro Swiss Dual Gear extruder on an Ender 5 plus/pro. Use 2 M3x8 screws to mount the spacer to the stock bracket. And 2 M3x20 screws and nuts to mount the...

This is a re-designed bracket to utilize Micro Swiss' Direct Drive extruder configured for linear rail. Additionally - I designed a cable relief bracket to help with cable management. ...Be careful with the mounting hardware - bolt length should be...

If you've installed the Micro Swiss Direct Drive on a CR-10s Pro like I did, you'll need to replace the Bowden/Filament guide that comes with it because it only fits the Ender3 or the CR-10. I suggest printing this upright without the nozzle facing...

This is a remix of the SATSANA Ender 3 Remix for Micro - Swiss Direct Drive + BLtouch. This works with a Noctua nf a4x10 fan for part cooling and a Noctua nf a4x20 for hotend cooling. It's a lot quieter and more powerful compared to the stock...

I took the base and gantry adapter for the Micro Swiss direct drive Ender 5 plus and remixed it to be magnetically attached. ...I'm sure it's not perfect, but it works great for me.</p><p>Link to the magnets I used:&nbsp;</p><p><a...

Fan shroud and probe brackets for the Micro Swiss NG REVO Extruder for CR-10/Ender-3. These parts are designed specifically for the M3301 model number NG REVO Extruder. Verify that this matches your NG Extruder model number before printing out any...