swiss micro 3d models

This is a remix of the Micro Swiss model that will allow the filament exiting the runout sensor to feed directly into the extruder's PTFE tube for seamless filament loading. Print in the orientation the model loads in. Supports may be needed...

I recently decided to upgrade my part fan on my cr-10 by installing a 40x40 noctua fan, which I had previously used and enjoyed with the EPF Fang for Micro Swiss all metal hot end designed by Metalurgia. To adapt it for use with a 40x40 part fan, I...

was flabbergasted that despite the multitude of various fan ducts floating around Thingiverse, NONE of them seemed designed for the CR-10S Pro V2 and Micro Swiss.This duct is designed for:CR-10S Pro V2BLTouch SensorStock fansMicro Swiss Direct...

This model makes the Bondtech created LGX Lite perch mount compatible with the Micro Swiss all metal hotend. The hole has been expanded to 8.3mm to accommodate the top of the hotend. ...Remove the compression nut from the top and this slips over...

This is a quick and dirty remix of redpiyaya's Micro Swiss NG wire harness to add a filament sensor holder. I made this quickly in Tinkercad, the hole placement for the filament sensor isn't perfect but its close enough for my needs. ...I hope someone...

Very basic extruder fan and blower mount for the Ender 3 V2, to be used with the Micro-Swiss Direct Drive Extruder kit (which did not have an official fan mount as of 1/2022). ... Includes cable fork to hang the cable bundle out of the way of the...

Which this part attaches This is for a Micro Swiss Linear rail Direct Drive (ender and CR series), where the Drag Chain goes left then under the motor. Any Material will do as long as the material will bridge easily with no support. One slot to...

This a quick and dirty remix of redpiyaya's Micro Swiss NG wire harness (https://www.thingiverse.com/thing:5382758) to add a filament sensor holder. I made this quickly in Tinkercad, the hole placement for the filament sensor isn't perfect but its...

... duct fits on the following hotend mounts: https://www.thingiverse.com/thing:4391060 It has a better air flow and less flow losses and it provide a better air flow to the Hotend. ... It still works with micro swiss and original Hotend. ...

This is a Cable guide for Micro Swiss Direct Drive Extruder Ender 3, Elegoo Neptune 2 This guide makes for a better and nicer cablemanagement you also keep the full build hight of your printer all you need to mount this thing are cable ties (3mm...

Check the amount of cooling fins on your hotend and print the matching fan shroud.Specific parts the fan shroud was designed forExtruder: M2601 Micro Swiss Direct Drive Extruder for Creality CR-10 / Ender 3 PrintersHotend Option 1: Micro Swiss M2583...

... of this object. ... I used AnthonyB's screw/nut mount, and made a slip on mount for the Micro Swiss NG pancake stepper. <b>NOTE: YOU WILL NEED TO ROTATE THE STEPPER 90Deg TO BE ABLE TO USE THIS OBJECT. ...CHECK THE PHOTOS FOR PROPER ORIENTATION!</b>

Very basic extruder fan and blower mount for the Ender 3 V2, to be used with the Micro-Swiss Direct Drive Extruder kit (which did not have an official fan mount as of 1/2022). ... Includes cable fork to hang the cable bundle out of the way of the...

This is a modified base for the Ender 3 V2 with the Micro Swiss Direct Drive upgrade. The rest is printed from the BullEye stl's. https://www.thingiverse.com/thing:2759439 I've changed the cable management, that was interfering with the direct...

*Print Settings* Material: PETG Supports: Build Plate Only Infill: 20% *Specific parts the fan shroud was designed for* Extruder: Micro Swiss CR-10 Direct Drive Hotend Option 1: Micro Swiss CR-10 All Metal Hotend (4 finned cooling block) Hotend...

simply modified version of a cooler and shroud so you can use ender 5 micro swiss direct drive modification and I modified a cooler to accept a 5015 blower fan for that I used 4 20 mm long m3 screws and 2 m3 nuts

Remixed from SATSANA Ender 3 Max Remix - Micro Swiss Direct Drive (No Probe) I added a stabilized mount for a BL-Touch ABL with space for the fans so you can print it all in one and have it neat and flush.

Adaptor to mount Micro Swiss Direct drive for Ender 3 Pro to 3DFused linear rail X-axis gantry kit. Suits standard Ender 3 fan set up with or without BL Touch. ... Shims may be needed with BL Touch depending on the x-axis limit switch set up.

Here is a modified mount for a BLTouch/3DTouch to work with a "Micro-Swiss All Metal Hotend" (or clone). This type of hotend is a little bit shorter than the stock hotend of the Ender 3 (Pro), so with the stock mount the touch pin can not be fully...

Here is a modified mount for a BLTouch/3DTouch to work with a "Micro-Swiss All Metal Hotend" (or clone). This type of hotend is a little bit shorter than the stock hotend of the Ender 3 (Pro), so with the stock mount the touch pin can not be fully...

... 300x300. ...it's abit more too the back since the bed cannot go completely to the end. Most importantly it's 300x300 again. Check my other designs for the Y endstop. Printer: Creality Cr-10s pro v2 Mod: Micro swiss direct drive extruder with hotend

... ... This moves the Y endstop 6.5mm to truly allign the bed. I also added X-Y-Z since i always forget that... NO MORE! Check my other designs for the X endstop. Printer: Creality Cr-10s pro v2 Mod: Micro swiss direct drive extruder with hotend

Remixed from - Satsana dual fan remix by BobanaPirate to fit on my Ender-3 Max with the Micro Swiss direct drive extruder. Changes made: removed the clip that held the cables up above the fan shroud because it interfered with the direct drive...

This a quick and dirty remix of redpiyaya's Micro Swiss NG wire harness (https://www.thingiverse.com/thing:5382758) to add a filament sensor holder. I made this quickly in Tinkercad, the hole placement for the filament sensor isn't perfect but its...

I've created a fan duct vor a 40 mm fan speacial for the Micro Swiss All Metal Hotend.There are two versions: One for countersunk and one for flat screws.Print SettingsSupports: YesResolution:0.16Infill: 20 % Cura settings:Buld Plate Adhesion: Brim...

The PTFE hose must be cut as follows:: === PTFE tube from sensor to extruder: 11cm PTFE tube from filament to sensor: 8cm Material list: ==== PTFE Bowden Hose Micro Swiss Bowden Dual Gear Extruder Creality Filament Runout Sensor Kit Filament I have...

The micro swiss bowden dual gear extruder doesn't line up with the runout sensor on the CR-10s Pro V2, and likely any creality printed that has the runout sensor on stilts. This design positions the runout sensor in line with the filament path when...

Not Nice but Stable ORIGINAL BASE NEW FAN BASE FOR STOCK AND E3D NEW COLDEND ADAPTER FOR ALL CR10 Stockend & Micro Swiss AND ALL CHINA CLONES Combine the CR10 or Micro Swiss and similar hotends with an E3D / J-Head hotend holder. This facilitates...

While investigating various techniques for printing with two materials (at potentially different print temperatures), I stumbled upon the simplest method: 2x "CR10 hotends" (as available on AliExpress), "Micro Swiss Hotend" clones 1x worm screw to...

It is a remix of the remix https://www.thingiverse.com/thing:4408571SATSANA Ender 3 Remix for Micro - Swiss Direct Drive + BLtouch. In this remix, the cooling ducts were lowered by 2.5mm to point below the nozzle. It's a test, I still have to print...