swing with cup holder 3d models

I designed this around a Pixel 6 Pro with a D Brand Grip case and an LTT store Waterbottle.The Inside Diameter of the bottle holder is 3.85.I've also included the puck to drop into the holder if you need to put a smaller bottle in the...

You will have to dremel the bezel to make room for the Cup Holder. I did not model to sides of the cup holder. I put an LED into mine and like the look of an open void. ...Also added USB charger ports which i wired to the stock cigarette lighter wires ...

Bowling ball holder with text, trying to make customizable You can use Openscad(free software) To change the text and the text variables. Ive been trying to get makerbots customizer to work on here but its being difficult. The File that says AIO has...

... ...Threw one together. Recommend to use PETG since it will likely get wet. Recommend to rotate it to lay flat on the print bed to avoid supports. Should be a drop in replacement for the existing handle and useable with the existing screws from the cup.

We've got you covered now with a portable drink holder on your crutches, ready for action whenever thirst strikes! Feel free to tighten it if needed, as those holes on the bar make quick work of getting a secure fit. The perks are plenty: It's...

The mascot's glass holder is emblazoned with its name.

I really liked the original model but I needed to be able to hold a larger drink so I made cup it can hold larger and solid.  The original clasp will be required for this and will fit on this. ... This will still require supports due to a small part of...

... for a glass on our nightstands in pitch black. ...So I thought up a simple solution to it! Here’s a cup holder that clamps onto the edge of most anything! ...Works best if there is a piece of clothing in between the end of the screw and the surface.

The updated iPhone holder incorporates an amplifier horn in front of the speaker output and a smaller version for the microphone. This design enables most components, except the phone holder, to be printed without support. The large horizontal span...

The Chip Holder was created by MathGirl on the Thingiverse platform, specifically with thing #350083 as her reference design.

My Little Artist Needs a Special Cup to Mix and Create.

I carefully selected and utilized these suction cups, specifically designed for a precise fit, which can be found on Amazon at the following link: https://www.amazon.com/gp/product/B01FGWVEKG. Using my 3D printer, I successfully printed them with...

A standard coffee cup sleeve bears a distinctive Batman emblem, giving it a sleek and modern appearance that is sure to appeal to fans of the iconic superhero.

This is a painting handle capable of holding miniatures with bases of 32mm in diameter. The handle makes it much easier to hold a miniature during painting. No need to use any type of putty, since the bases should snap-in. I used the holder from...

... and bolt for the joint the default instead of it printing in place and warping mid-print. There is also a support piece included to make sure the piece you place your cup on is properly supported against the wall meaning it can support more weight.

Drink Holder for Your Automobile Insert Printed Instructions on Your Fabricated 3D Printing Model ABS Filament Layer Height: 0.2 Millimeters Fill Density: 20 Percent Scale Your Dimensions to 25.4 If Necessary

Used two magnets to close it. ...Don't need the holder around the bottle because it is not used while driving, so it's more like a tablet that you can close if you don't need it.

Design Chip Holder is made using the model by mathgirl, which can be found at thingiverse.com/thing:350083. Tinkercad created this design, and users can edit it online at tinkercad.com/things/imkCF3ihKnH. It's unclear if these chip holders meet size...

Inspired on the Redgrass RGG360 ergonomic miniature holder, I started to design just its cap to have replacements, but finally I decided to redesign the whole hand grip so I could print the whole hand holder on my own. It needs a common 608 ball...

Grabbed the excelent design by danielolivier and added a few shenanigans to allow for the water to leave. ... Printed with 30% infill with white pla

Use 2" standard net pots. ...This has locking tabs on the inside so that the pot does not sag or come out. The pots are flexible enough to insert and remove. Print with tower suggested settings

... original design for this eggcup: http://www.thingiverse.com/thing:904510 Tried creating the same design in another program. ...This time I used Autodesk 123D Design, giving it a sleeker appearance. Printed with Robox, no support material was needed.

To bring this concept to life, you'll need a tube with a diameter of 10mm. Some notable changes include: Stackability: The redesigned rocket stand is now compact and stackable. Printability without Support: The updated model can be printed without...

I printed with Gyroid infill @ 10 percent but could be lower, 4 top and bottom layers, .6 nozzle and was on Ender 6 but isn't an option which is why I selected the nearest to my Ender 6. I have broken the part into two pieces for easy printing...

The container can be used with or without the print-in-place swing lid. ...Included versions: the Body with 230mm height (default) the Body with 210mm height the Lid – print-in-place (default and recommended) the Lid with both parts separated – print...

In blending swing and servo-horn, I crafted a design that includes a screw hole extending through the base for simple attachment. Cleaning all plane surfaces is optional; the print still results in high quality. ...The model necessitates support during...

The container can be used with or without the print-in-place swing lid. Included versions: A: Regular Body_regular: The body with a height of 230 mm (default) and a thickness of 0.8 mm Body_regular_lower: The body with a height of 210 mm and a...

swing

SWING

This is the exact same as the original Boston Power battery holder by jdeadman but with the mesh fixed for Cura