sv06 plus 3d models

Modelo para teste de nivelamento. OBS. ...retire a adesão para não sair da area de impressão.

Tested tool holder for all included tools from Sovol.

So I have one of these tiny cameras from AliExpress, which I think I was originally planning on putting closer to the nozzle, but then this happened. It actually works, too! It's not super snug though so YMMV. Bumping up the size a tiny amount may...

prints in two parts at stock settings for your material. the screen cover might need supports. make sure the supports are very low. ...the bottom piece slides onto the screen and the tool holder bolts to it.

So I made a previous toolbox with extra thingies mounted to it, remixed from one of SavageLau's designs. He made a new design, and I couldn't resist personalizing it. I made what I consider to be improvements:Caliper holder on the back (better than...

This is a simple printable spacer to fill in the gap left when you move your stock POM leadscrew nuts onto an Oldham coupling. The spacers fit below the Oldham coupling creating a flush surface. They have a 10mm hole to allow the leadscrews through...

A simple 5015 fan mount Printed in PETG 0.2mm layer height and 10% infillfor the screw that holds the fan its 3mm in diameter so it self taps into the plastic, make sure its at least 2cm longHope it works!

Tested tool holder for all included tools from Sovol. ... Installs with 2 M5 screws and T-nuts.

IT WAS SUGGESTED THAT IT WAS A WASTE TO NOT BE ABLE TO USE THE ROLLER BEARINGS FROM THE ORIGINAL SPINDLE, SO… I MADE A SPINDLE USING AS MANY OF THE ORIGINAL SPINDLE PARTS THAT I COULD. ...IT PRINTS WITHOUT SUPPORTS.ORIGINAL PARTS USED2X ROLLER ER...

Model pour déplacer le ventilateur d'origine à l'arrière et rendre visible la buse. PREVOIR VISSERIES X2 utilisé la platine de fixation d origine du ventilateur et ajouté deux vises supplémentaires. ... Ajouter des supports uniquement en...

Add 1mm cutout for nylon screed.

If you need the bed and the bed texture for your slicer here it is I made it for PrusaSlicer but should work with other as well

Remix of the pi case from Thing:4849204 to attach it to my Sovol SV06 To mount the case to the rail, the pin from this thing: https://www.printables.com/model/370389-sovol-sv06-enhanced-tool-holder/files was used. ...

Sitered Bronze Bushings Adapter for Sovol SV06 (mostly X and X Axes). This one is for bushing dimensions 8x12x20mm. ... Additional model: "Press in Tool" Made with Microsoft 3D Builder and Tinkercad.

... and slide the filament guide over the spool holder arm. Re-install the spool holder tube back on the arm, and you're done. Please post your makes. Update: 3/5/23 Added file “SV06_Filament_Guide_V1a.stl” This variation is a closed loop. ...No slit

The nozzles for my SV06+ are sticking out the box around 2.5mm. Can't close the lid, so I made the lid-receiving-part 3mm higher and removed the imprints. The lid is untouched. Die Düsen für meinen SV06+ stehen ca. 2,5mm über den Rand hinaus, so dass...

... snap the cover in place, re-connect the ribbon cable, and you're done. I designed this LCD back cover specifically for the SV06, but it might work with printers using the same LCD controller board. Prints without supports. ...Please post your makes.

The Sovol SV06 transfers about 50% of the sound it makes while printing through its feet. This contact noise can be removed with my dampening feet. It's quite springy and compresses about 5mm under the weight of the printer. ...Despite that the printer...

Make a new extruder knob for my SV06 in the style of the S.H.I.E.L.D. ...logo.I printed it in PLA with .20mm layer height, but use whatever works best for your printer it's a very simple and forgiving print.

------------------------------------------------------------------ This is version 2 of a SV06 Heatsink Fan Duct for 5015 blower fan which I designed for my model since I had heatcreep issues. Only use on your own risk. ... Fan holder remixed of...

Enjoy 2/23/23 Update: Added file "SV06_heat_bed_cable_clamp_V1a.stl" This revision includes small details that I excluded from version 1 because they are likely to disappear when sliced at 0.2mm layer height. The small details are a recessed area on...

This is just a simple texture and model combination for your Sovol SV06 presets in SuperSlicer or Prusaslicer. All I did was adjust the z position of the stl for the bed and quickly made a texture in Affinity Designer for the texture. It is loosely...

[English] I was enjoying 3D printing with SOVOL SV06 with Klipper, but since it got hotter, layer shifting of X-axis and Y-axis started to occur frequently. I tried various things, such as lowering the run_current value of the TMC2290 of printer.cfg...

I use RepRapper PETG White.layer height: 0.20mmSupports: RecomendedInfill: 15%[English]I was enjoying 3D printing with SOVOL SV06 with Klipper, but since it got hotter, layer shifting of X-axis and Y-axis started to occur frequently. I tried various...

If your SV06 cable chain is stiff and with restricted movement, then printer calibration is recommended. The spine should be very flexible and should behave like a very loose rope as shown in the video. The dimension for the cable clips is 1.2mm...

Please refer to the included pictures for proper zip-tie orientation.Parts needed:1) 2mm wide zip-tie or similar ( the extra zip-ties included with the SV06 work best )1) 3.6mm wide zip-tie or similarPrinting Notes:This is a small print that benefits...

Parts needed: 1) 2mm wide zip-tie or similar ( the extra zip-ties included with the SV06 work best ) 1) 3.6mm wide zip-tie or similar Printing Notes: This is a small print that benefits from a well-calibrated printer and prints best at a 0.12mm...

Bonsai pot for plus-plus

Since the very first moment I got the Sovol SV06, I thought about placing the Pi below the screen, so I present to you a three part design to accomplish that in an easy way. First part is a cover which snaps on directly onto the screen PCB, this...