sv06 plus 3d models

Needed a holder for a second spool on my SV06+, so I designed one.It incorporates the nut thats tightening the original holder, so unscrew the original nut and screw on this holder.Print horizontally as shown in picture to maintain its strength. Bild...

Zur Synchronisierung der beiden Z-Schrittmotoren, können mithilfe dieser Abstandshalter, beide Z-Achsen manuell auf gleiche Höhe gedreht werden.

I designed this part to keep my filament from unwind while printing with my spool side mount.No extra parts or screws needed, just replace the original part.I splitted the part in two for simpler printing and so you can mount it on the opposite side...

Hi,Ich habe mir einen Bauteillüfter inclusive LED Halterung gebaut, der den Druck auf das Optimum perfekt runterkühlt. Er ist von hinten Flach angebaut um Druckbettmaße nicht zu verlieren wie leider bei vielen anderen. Wird nur eingeklippt und mit 2...

Customized version of https://www.thingiverse.com/thing:3507663 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3507663

Customized version of https://www.thingiverse.com/thing:3507663 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3507663

Customized version of https://www.thingiverse.com/thing:3507663 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3507663

Scarce parts to install it. ... 2 pcs M5 45mm screw 2 pcs M4 16mm screw 2 pcs M4 nut

I had problem when connecting power cable for klipper screen,cables whould touch each other and i could not close it..So i created this extension and now cables do not touch each other and its safe to run printer when im not home.. ...Printed with...

Customized version of https://www.thingiverse.com/thing:3507663 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3507663

Definitely overbuilt, but I wanted to make sure the plastic is thick enough to resist warping from the bed heat.

This is my newest tool holder, it is still a work in progress.(As of right now i don't like the design as its very cramped needs work)Print on its side with the USB holder on the top.no supports neededprinted in PLA Let me know how it goes!if you...

Hi, I made brackets to test my Sovol SV06 Plus with Portable Input Shaper from FYSETC. This specific one is slightly easier to use - requires only USB-C and flashing firmware to it. There were no brackets available for SV06, so I decided to make one...

🙌 🙏Please take a moment to ⭐ star mjonuschat's and Andrew's repos.Sourceshttps://github.com/mjonuschat/PrusaSlicer-Profileshttps://github.com/AndrewEllis93/Ellis-SuperSlicer-ProfilesMy Sovol3d related repositories:OSS Klipper...

Home all your axis and put down the rod on this tool on both sides till it has a tight fitment

Dieser Halter passt zu dem ADXL345 des originalen Lieferumfangs des BTT Pad 7. ...2x M3x82x M3x204x M3 Gewindeeinsätze

Customized version of https://www.thingiverse.com/thing:3507663 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3507663

My drybox does not sit parallel to the filament guide, so sometimes the filament slips off the rollers. ...I made this simple bracket to keep the filament on the far right roller, although you can use them on all the rollers if you need to.

Customized version of https://www.thingiverse.com/thing:2202854 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2202854

 If you intend to use Sovol's SV06 Plus hotend, you'll have to get or make a duct that will work with the tall heatblock.I included a few models from Sovol's github, to include their extruder knob and extruder release lever, for no purpose other than...

adding a micro sd card extender to my sv06

I recommend 30 mm screw for Y axis variant and 20 mm for X axis variant.They are probably compatible with SV06 Plus and other printers that use M4 belt tensioner knobs and 128640 type screen.I'll probably update this page with more Extruder Knobs...

The best places I’ve found to mount a Pi on the Sovol SV06 and SV06 Plus require drilling and tapping so I came up with this “backpack” concept to clip onto the controller housing. It lightly plays into PLA’s compliance to hold firm and has a...

Ein Kamerahalter für die rechte Seite des Sovol SV06 Plus, wenn der Touchscreen auf die linke Seite montiert wurde.A camera holder for the right-hand side of the Sovol SV06 Plus when the touchscreen is mounted on the left-hand side.

I was using the very popular (and cool looking) cable spine for my SV06 Plus but found that the weight of it added some strain to the both ends of the cable. ...Instead I made a small clip for the top of the 3d printer to hold one of those generic...

Yesterday, 06. ...April 23, i got my preordered Sovol SV06 PLUS... i like it really... but i hate to handle with Micro-SD´s so i designed this to Insttall a Extension for normals SD-Cards.... ... Have fun!

I Made this for the SV06 Plus to place your tools and things needed. No supports needed on my printer, set fan to 100% for PLA, other materials im not sure about bridging settings but does well with PLA. ... If you have any requests for things let me...

Remix of Paul_3D's awesome spool holder for the SV06/Plus. This will now be wide enough to fit Polymaker 3kg spools. There are two versions of the base, one that is just normal extension and one that has a stud mount to accept a 608 bearing filament...

sv06 logitec c270 mount remixed to be able to mount on the sv06 motor axis

Made for the SV06, I don't know if it will fit other Sovol Models. Res: 2 Infill: 30% (For Ball) Print Time: 50 Min. ... No Supports