surface pen holder 3d models

I tested it out and it seems good, but to stop the weight of the cables plugged into the dock pulling it back I used some Command Strips on the bottom of the dock holder to keep it in place. Bill of MaterialsRequired: 3D printer and filament (inb4...

This is where I remounted the stock spool holder, though beware it needs to be under 85mm in length which fits pretty much all 1kg spools for the bed to clear it at around 350mm on the Z axis. You will need to drill holes for wiring to be run into...

 A flashlight shining through the slit in the hole is your friend.Insert PTFE tubes into the front of the buffer and route to your preferred spool holder system.  If using an enclosure, this will probably involve drilling holes through the enclosure...

In this thread i will add the 3D printable improvements that go specifically designed for this model all ready Done: Power PCB Support <Future improvements: Led light for Tail / Nose, Camera Supports ,GPS Supports, Battery holder. <I don't know. ...

A dab of super glue can help keep them in place) 2x M3 Nuts Mounting Z Axis with POM wheels 2x Bracket_Spacer.stl 3x M5 Washers 1x 2GT Open Synchronous Timing Belt 6mm Width, 1M Length You'll need around 67cm, I don't have an accurate...

Use (2) heat inserted knurled nuts at the back of the Carriage top and mount the Carriage PCB holder into these knurled nuts. Slide the X linear rods into the linear bearings now mounted to the Carriage assembly. Install all the original parts into...

I also have a re-designed x-axis belt holder since I went with some off-the-shelf parts from amazon and openbuilds. I ended up going with two aluminum gantry plates, one on either side of the c-beam, then used an aluminum NEMA 23 mounting plate for...

The spindle holder is designed for a 52mm diameter Chinese mini lathe (cheaply available at hardware stores and tool shops). Both nema 17 and nema 23 motors can be used. I use all nema 17 motors but I plan to extend the X axis and Z axis motors...

&nbsp;Hello reader,here is my instruction for an easy to use and build ticket, picture or coupon holder. I already tried to find a good solution with the laser cuter, but was never really happy with the end result.(The other Versions <a...

That was one of the first mods I did, right after the rear spool holder. My printer is getting old now and the carriage that the cartridge slides into is getting kind of worn and sloppy. It just doesn’t hold the cartridge nice n tight like it used...

I also created a thermometer holder that is designed for the Acurite Humidity Monitor available at Home Depot. This will allow you to monitor the internal temperature and humidity level of the enclosure as needed, and will also allow you to...

Another upgrade I had planned was to replace the 2 extruders as I didnt like where the release levers were mounted, having them inline with the filament made it awkward to feed material, and hold the lever while twisting my arm around the spool...

Print profile is in the attached 3MF file and Gcodes, which are for a CR-10 upgraded with a BTT SKR Mini E3 V1.3 with MicroSwiss DD extruder and dual Z stepper using Klipper.&nbsp;Build instructionsSwitch off and unplug your printer just to be...

It is a remix of the original spoolholder that uses printed roller arms and springs to press the spool down.To improve the stability of the arm, the profile was divided into two halves, the lower one containing the bushing and separated by a gap of...

Axle parts: Housing 5mm Bearing holder Housing backing Frame parts: Frame parts are able to rotate to fit together. There is the ability to add 2mm steel rods through out where they join. Length range 40mm to 100mm. 40mm are the holes that line up...

This LCD cable holder will be easy to install because you already will have the frame ends exposed. You need one more FrameBracket2 and the LCD clip. <a...

Remove the paper from the other side, and firmly press the part against the interior wall of the plastic box in the marked locations, making sure that for the brackets, the U shaped rod holder is facing up, and for the passthroughs, that each is...

Headlight + handle req: ABS filament to print holder, 2 flashlights, 2 Samsung 18650 batteries, 2 M4 screw + nut (15mm long approx.), flexible orange band for handle. I don’t think it’s a big deal, but it would be if the flashlight was any closer. I...

repeat that with the velcro cable holder on the other side. For the box, assuming you are using the waterproof version, use the box held flush against the back of the handle so it isn't obstructing the roller to locate and mark the 3 holes for the...

I have shortened the magic band reader holder post to be more to scale with the rest. I as well added a half inch hole through the post and the plug to be able to past wires between the electronics without drilling, half inch might be oversized but...

a clamp to add some tension to the bearing, or a holder for eyepieces or other accessories.MakingCut the aluminium tubes to size. The four legs need to be cut fairly accurately, there is some room for play but not much; try to get at least within...

TL;DR first: Welcome to my Overhaul of the Creality Ender 2! Im starting here with version V2 (V1 is only in one picture; there was too much wrong with that), which comes in 2 iterations/stages: ++++++++ Stage 1: ++++++++ changing out the Heatbed to...

- PINDA Adjustment & Positioning Tool(Achieve the perfect SUPERPINDA position)MMU2S Single Filament Guide Festo M5 Coupler(Retain your original MK3S spool mounting while still using MMU2S in single color mode)Nozzle Holder Case Ultra(Biggest and...

(if you want to go faster tune the speed up to 130%)All the stls are in the right orientation.The back plate can be laser cutted or 3d printed, all the files are included.Prints the following parts:1x PanelMeterClock_v1_Body: Prusament PETG, Preset...

Bend the rocker switch pins so they don't touch the first battery For those who have already printed the first version https://www.thingiverse.com/thing:5418531 only print parts 11,12,13,14,15 to upgrade to V2...

...Anyone may print copies for their own personal use, but selling or otherwise monetizing them is not permitted, and puzzle designers retain all rights as copyright holders of their work.Our puzzles are modeled using the open-source puzzlecad library.

It fits my battery holder very nicely, and I drilled two small holes to run the wires down into the body (hence the small notch in one side). I did a layer change at the top so that I could print the "exhaust pipes" in silver. I found them here:...

Print the light bar and 3 of the nut holders. (Steps 1 & 2 from the non-switched version) 3. Clip the ends of the mini rocker switch so they fit inside the enclosure once it is inserted. 4. Loosely place the LED strip and switch where they will go...

### Required Hardware: ### Here's a list of items that will need to be bought in order to make this boat go: * Metal Gear Micro Servo - 2pcs * M2x10mm Screws - 9pcs * M2x3mm Threaded Insert - 9pcs * 2x 18650 Parallel Battery Holder - 1pcs * RC...

Filamet spoolholder X2The filament spool holder X2 for Prusa MK3 can hold any 1kg standard spool (also the 2kg Prusament PLA Recycled) as well as with the 2 different extensions spools up to 4kg or a maximum spool diameter of 350mm. The optional...