sureflap rear cover 3d models

TRX-4 DriveShaft Cover Rear v3 (Chassis Kit) Important Note: Secure with Cable Ties This part was printed using the Anycubic i3 Mega and Cura 3.5.1 software. ... Printing Settings: Layer Height: 0.2 or 0.1 First Layer Height: 0.2 Infill Density: 20%...

This is a replacement cover for the rear wheel swing arm on an old BMW R80ST from 1983. The original BMW part number that this takes its place is 33 17 1 230 296. My sister's bike had one vibrate out, so what can you do with a printer? After...

This is a Rear Plate Cover add-on for the MAZDA RX7 engine.Original :https://www.thingiverse.com/thing:3006071The video of the finished project : https://www.youtube.com/watch?v=O1ecJfzF-9Q Printed parts list (1)1 x RearPlateCover : Layer:0.15mm...

Was tired of loosing the dust cover for my motorcycle's rear swing arm bearings, so I designed one that fits tighter than OEM. Will fit many BMW R-series bikes from the 70's through the 90's. Printing: Every layer height and orientation worked...

This is a rear top cover with cable loom support for the Ender 7. This fills the gap in Ian's excellent Ender 7 top cover. The stepper motors are now covered and the cable loom is supported. Minimal support is required if printed with the cable entry...

This is a pulley cover for the rear Y axis pulley on the Anycubic i3 Mega (I guess it's a gear attached to a stepper motor, not exactly a pulley, but that's what everyone is calling it so we'll go with that)I decided I wanted some pulley covers, and...

-------------------------------------------------------- A snap-on cover for Hasbro's Ghostbusters Plasma Series Spengler Neutrona Wand to make the rear grip more like the 1980's Proton Pack Neutrona Wand. Print in a vertical orientation. I wanted...

Replace the rear coil inlet cover with a new one. Printer model: Davinci Pro 1.0 3-in-1 A small design enhancement allows for easy insertion of the 3D filament into its inlet. Filament inlet diameter is exactly 3 millimeters. To achieve precise...

This is a quick and dirty designed cover for the rear left corner of the PrusaBox to hide the cables. It is designed to use with my magnetic cable duct (see here...

Dummy Parking Sensor Hole Cover 18mm Front/Rear Bumper You can buy it in our store:https://www.ebay.com/sch/jjeffrey_73/m.html?_nkw=&_armrs=1&_ipg=&_from= Please feel free to share images of your prints on this page, I would love to see 'em. Leave...

This rear vent cover for the Creality LD-002R SLA printer lets you attach a 3" duct hose to exhaust the fumes. To do this, you'll need a clamp if you're using a 3" hose, since the port's diameter is only 70mm - just shy of 3". If you prefer to use a...

This is a rear panel cover for the PiStorm32-lite HDMI and MicroSD Card extension, with the IndivisionAGA mk3 HDMI port available in the same place. It is very tight with where the IndivisionAGA HDMI port goes - that needs to be on the left hand...

I needed a new rear cover for my Wanhao i3 printer control box that could hold a larger fan and move the wiring loom forward, giving me some extra space since my control box is underneath my printer, which sits in an Ikea Lack Cabinet. I looked...

This is the Mrk 1.8 of the Rear Battery Cover clip for the Harley Davidson Sportster 05 and later. Note:  *When in slicer rotate the model to place on face like the photos to reduce the amount of supports need it to print.             *make sure to...

This is a modified version of the Rear Cover Plate of the Spot Micro Esp32. It allows for the integration of a Lilygo T-QT Pro (https://www.lilygo.cc/products/t-qt-pro). I think it's a cool gimmick, and you can control several things with it. It can...

This is a snap on cover for the rear motor and pulley on the Y axis of the Ender 3 Pro. It may not fit the Ender 3 because that printer has a 20 mm Y axis and the Pro has a 40mm Y axis beam.</p> <p>Simply print it and snap it on. No supports needed.

Replacement for car jack cover A2086982730

Replacement for car jack cover A2086982930

I made this to protect my rear belt from kicking up rocks.

roughly 20 min process after you print this and remove turn signals, see steps below: -Remove Rear turn signals -cut a 4x4 piece of foil (take the foil and press against where the turn signal mounted make sure you get an imprint of the screw hole as...

The original cover has the power plug mounted on the side of the printer, which limits my options for space within my enclosure. To remedy this, I've redesigned the piece to accommodate plugging into the rear instead. This revised design uses all the...

... through 2000 model Opel Tigras. Installation required. Complete and accurate reproduction of original factory made piece designed for rear passenger compartment of specific vehicles manufactured during 96 thru to year two thousand's middle years.

... the top deforming due to the leather and the screw holes. if you think bolt holes would be better I could do a version that permitted through bolts but I thought that would look crappy, and the cover is right there in the passenger's eye line.

To cover your holes. Like the real deal. ...

C4 Corvette Rear Sun Shade Clip Drivers Side better than OEM. These clips make attaching the cargo sun shade easier. Trust me! ... See Passenger Side as well!

Rear Panel Upgrade Kit for Thanos AMC AASD Controller Enables Easy Installation of RJ12 Socket, Perfect for Emergency Stop Button Integration.

C4 Corvette Rear Sun Shade Clip Passenger Side better than OEM. These clips make attaching the cargo sun shade easier. ...Trust me!

The replacement gasket for a JBL 2426J speaker, this crucial sealant is specifically designed to fit snugly onto the rear panel.

This clever solution frees up valuable real estate within the printer's workspace by relocating the power plug to its rear.

It can be held in place either by folding the rear seat forward or with a ratchet strap around the seat, using a block of wood to focus pressure against the mounts. Adhesives worth considering are long set epoxy, gorilla glue, and GE silicon clear...