surefire pressure pad mount 3d models

Pressure pad mount for Surefire Chinese Flashlight replicas. The pad stays snug and doesn't move. Has two cable routing zones (3 mm clearance, enough for the pressure pad's cable, you can pick which side the cable goes into). Uses 5x30 mm...

...So you don't need to waste that stock pressure pad! ... Optimized for FDM printing, inner holes are slightly enlarged. The pressure pad is fiction fitted on the mount, need 2 M3*25 cup head 2 M3 nuts

A snap on Picatinny rail mount for Surefire Pressure Switch. Once put on it's very hard to take off, decide carefully before applying. ...Tape can be used to stop the pressure switch from sliding out.Print right side up, with support and brim.Design...

M-LOK Mount for SureFire Pressure Switch Installation Requires M-LOK Nuts.

Shortening bolt pattern width to allow 25mm long screws (thus avoiding screw trimming) added extra chamfers and radii to make design a little smoother and nice **** This is a Pressure Pad mount I designed to hold the stock Surefire Tape Switch. The...

Add additional structure to lock in M-Lok mount. May not suit for Key-mod. Haven't been tested. V2.1 shall not work, so I made a V3. Just use V3. This time it shall work. I'm not good at modeling, but it shall works. I'll test print it today. ...

This is a 28mm flashlight mount with support for pressure pad. ... Items required: 2x M4 x 30mm, 2 nuts and double side tape.

This is a 28mm flashlight mount with support for pressure pad. ... Items required: 2x M4 x 30mm, 2 nuts and double side tape.

an m-lok rail mount for ultrafire style flashlight

Remix for deeper Screws

A pressure pad model is an apparatus designed to detect weight distribution and pressure points when stepped on. It's often used in various settings such as healthcare, ergonomics, and biomechanics for research or diagnostic purposes. ...The data...

A leg pressure pad is essential for providing relief and comfort to individuals experiencing discomfort or pain in their lower extremities. This device helps distribute weight evenly, reducing strain on specific areas and promoting better posture.

Helmet Mount with Velcro Baseplate for the Surefire HL1 Tactical Helmet Light. ... 360deg rotatable with notches.

This will mount to an Arc rail for a Surefire head lamp

SureFire pressure switch holder for NATO spec picatinny rail WARNING (This is a tight pushfit no need for fasteners) very tight tolerances. ... printed vertically with switch wire hole at bottom Currently 3 sizes - perfect fit ...

I built a helmet mount specifically for my Surefire Helmet Light HL1-C, ensuring it would be a seamless fit. To get it right, simply print the object vertically and use hexagon infill to achieve maximum strength. I opted for Z-ULTRAT filament, which...

This versatile mount can be attached anywhere you need it - on a phone, in a car, even on an RC model or wall - thanks to the Scotch outdoor mounting double-sided tape applied to its back side. Simply stick it where you want it and enjoy! Firepak...

SF Mount for Mlok Handguard. ... SF mlok mount 7.6 was designed to fit to 'RGW M-LOK Rail Kit for Cybergun WE SCAR GBBR', SF mlok mount 7 was designed to meet the standard Mlok specifications(7*32mm). You need two M4*10 flat head screws. ...

... knife</li></ul><p>You need:</p><ul><li>2x M3x8 screw with flat countersunk head</li><li>1x M3x10 screw with flat countersunk head</li><li>3x M3 nut</li></ul><p>p.s. secure light with e.g. ranger band su you don't loose it if the mount break :-)

Visit my Etsy store! I created this picatinny mount for budget pressure pad users in mind - I wanted something better than tape or command strips. Works on airsoft AND AR, standard 1913 rail dimensions. Two versions - rounded, and squared...

This is an easy way to mount a Surefire Macrostream to any firearm with a M-Lok handguard. ... Print this at a 45 degree angle for best results.

Adapter mount for Surefire HL1 helmet lights. Current screw holes are configured for Ops-Core ARC Wing-Loc rail adapter (20-98-103) but use the .step file to adjust hole size and position to suit your mounting requirements. Tolerances in the design...

[01/05/2022] UPDATE: All files migrated to Printables: https://www.printables.com/model/186741 Adapter mount for Surefire HL1 helmet lights. Current screw holes are configured for Ops-Core ARC Wing-Loc rail adapter (20-98-103) but use the .step file...

**It doesn't look up all the way because of the GoPro mount**, but it'll make about an 80 degree angle, so that's good enough for me. If you have any questions please ask in the comments! ...**Post a make if you print it!!** **Other Cool...

Originally, I tried to use double sided tape to stick the rubber pressure pad to my replica, but obviously the tape would not stick to the rubber. Instead, I modeled up a quick tray the pressure pad mechanically clips into, then the tape sticks to...

... mount to keep it within easy reach when working in my shop. Here's the light: https://smile.amazon.com/SureFire-Dual-Output-Flashlight-anodized-aluminum/dp/B009F7J8LQ/ref=sr_1_1?s=home-garden&ie=UTF8&qid=1525264212&sr=8-1&keywords=surefire+6px+pro

I finally made a proper spotlight for the Surefire Hellfighter Mount. If built to my directions, the Spotlight Frame will slide and lock onto the M88 Mount. The spotlight cover is designed to open an latch closed. You can mount your own light in the...

This is a low profile mount for scout flash light Compatible with M300 and M600

I remixed this to only use 3 slots

American made helmet mount. ...Mesh is based on the SureFire HLM-01-TN.