supurbe models

The "Advanced_Fit" version is meant for printers with tighter tolerances and may provided better heat break cooling due to the extended cooling channel.** After looking at all the options for a hotend mount here on Thingiverse and Facebook i decided...

You can also see more on this and other projects by check out YouTube Blog: http://youtubeblog.diy3dtech.com Parts List: uxcell 3mmx5mm Brass Shaft Coupling Coupler Motor Transmission Motor Connector for RC Boat Model: https://amzn.to/2VLJvfZ...

In Cura, this can be accomplished by selecting the model, duplicating it, and then choosing `mirror` and selecting the red and green arrows. `Langstroth Frame Top 2 piece.stl` - **Print 1x, 100% infill, Duplicated per instructions** This piece is...

UPDATE: 07/16/2019 Project 399 - Front Crossfire Mount - Depressed 3525.stl - I've been running this model the most. I thickened the sides so it provides more lateral stability, improved the chamfer at the sides to make it smoother, and I thickened...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

If you do this, use the "Pusher Extd" model. To modify the solenoid: 1. Remove plunger. Remove about 3mm of the black base and sand flush with the metal slug. Sand the black base to make it slightly thinner if you want to add an additional spring...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

These elevator models have been designed with very specific fit tolerance, to make these pieces fit tightly but not too much that you can't snap them together. Here are some general considerations:Print with PLA. But they also work with PETG, ABS,...

You may have to rotate the model so it sits correctly on the bed. Post-Printing ============= Checking the fit and gap. Angle so you can see the handle position. Body is all the way in. The ends of the handle (parts under the lip) rest against the...

... cut methodology used. All credit for the idea to use them as puzzles goes to Quadratum Cubicum (QuCub.com - no author name noted) and this was already licensed under Creative Commons Attributable before I modeled the pieces and the base/lid. ...

This is how it should look like:You can use support enforcers to remove the unnecessary supports in the slots for the IO of the electronics (it works by bridging)I printed it at 0.3mm layer height, 10% infill.If your bed is too small, you can split...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

Tensegrity model maintaining stability with one single wire.Materials needed:0.5 mm nylon wire7x M3 nuts7x M3x10 mm Allen screws (longer ones were cut to the right size)wooden plank of about 55 cm2x 50 mm wood nailsThe spiral parts are designed to be...

The spacer is to put between the 5015 fans and the cover, if your spacing is larger/smaller just scale the spacer on the Z axis to match your setup. The hole for the mounting screw is designed to be 4mm in diameter, but if yours end up being...

Print the bumper pin two more times (for a total of 3 bumper pins) and print the pusher pin one more time (for a total of 2 pusher pins) Before printing out the ball, slice the model in half horizontally and rotate the bottom half 180 degrees...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

 For me, it pressed in very tightly; if in doubt, glue it in.To mount the holder, I stuck this adhesive mount onto the back, and used it to replace the jaws of an older model of this suction base.  The adhesive mount’s socket is smaller...

&nbsp;After getting the other nosecone to work I found out that the original Sprint used a BNC-50X and I had modeled off the BNC-50Y. &nbsp;So for ‘authenticity sake’ I've added a BNC-50X version of both the stock and Astrocam nosecones.</p><figure...

In order to make it much easier to assemble the case with the RPi4, a few changes were made:Divided the lower part in two halves for easier inserting ofRaspberry Pi;Added snap fit link between upper case and lower case;Using four M2.5x4 screws is...

Sincethis design is compatible with a whole variety of lampshades, be aware that somelampshades will have to be scaled down or up to fit the base's default settings.&nbsp;Base- Layer height: up to 0.3mm is fine, there's little detail on the Z-axis-...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 19 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 45 use_stencil = 0 stencil_size = 40 stencil_shape = 6 stencil_mirror = 0 custom_back_extra_port_x_size = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

It started with a Bachmann starter set with a steam loco and a couple of cars (Durango & Silverton in case my other models didn't give it away). This came with a bunch of EZ-track. I had full intention of expanding my layout so I bought more...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_width = 100 use_mouse_ears = 1 pattern_element_overlap = 0 stencil_shape = 7 custom_back_camera_y_size = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...