supportfan 40mm for extruder with layer cooling 3d models

*very important note!!!!!* if you're going to build this remixed set, you may/may not need to shave off a little bit of the hotend clipper's bottom if it is colliding *if you are going to make this,make sure to read everything that is written here*...

I designed this adapter for my TevoTarantula motherboard, which can accommodate either an 80mm fan or the original 40mm fan. The design is mine. Tolerances were used to create the holes. Let me know what you think and if any modifications are...

... However, it may generate a higher pitch noise and decrease cooling effectiveness due to increased blockage, so a higher flow rate fan might be necessary. It is ideally suited for 0.4mm nozzles with most honeycomb structures measuring 0.8mm in size.

I made this fan duct for getting cool cooling air far away from the heating bed into the fan. i wanted it to be as light as possible, so the wall is only 1mm. There is also a little grid to protect the fan from parts that could fall in or even...

The cost of replacing it was almost as much as the Noctua 40mm NF-A4x20, and Noctua's specs were impressive - approximately 5.53 CFM and a static pressure of .88in H2O. I now own seven of these fans, so I figured "I'll just replace it with a 40 mm."...

This is a revised design based on 3ddelta's Mk IV hotend cooling shroud, with an added benefit - it's been shortened by 3mm so that the Mk V hotend nozzle extends below the shroud's level. ...Additionally, I've reduced the thickness of the "U" keeper's...

I designed this fan duct to effectively draw cool air away from the heating bed and direct it towards the fan. My goal was to keep the weight minimal, so I made the wall just 1mm thick. Additionally, a small grid is incorporated to safeguard the fan...

I've created an adapter based on Mouse's generic parametric cooling fan nozzle to accommodate my Prusa Air 2.

I built a mount myself to cool my new system, designing it specifically to fill the need. ...The part I used is called an effector and can be found here: https://www.thingiverse.com/thing:824932

A DIY Kit for Installing an E3D V6 into a Solidoodle 3 (also compatible with the Solidoodle 2) can be easily created by remixing sources listed to integrate a bolt-on extruder brace that securely locks the hot end in place and adds mounting points...

Installing two of these tools should provide reliable results when paired with an E3D v5 hotend. ...Their design allows for hassle-free printing without needing support structures.

All of can be printed without support and they needs to be printed like they are aligned on the gcode or the 3mf files.(The PWM and FAN labels or just for my usecase where I use the FAN switch to turn on/off the fans and the PWM switch is for setting...

Human: Customized Version of Thingiverse Model 735038 Created with Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=735038 Custom Instructions for Use Operating the following Settings: Thread Wall Thickness: Set to 1.2...

This fan duct was designed specifically for fans with low static pressure, making it ideal for silent operation. I've found that it restricts airflow significantly less than other designs I've used in the past. I'm currently using this mount on my...

Customized version of http://www.thingiverse.com/thing:735038 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=735038

# Horns Duct - Layer Cooling System I've moved this design into its own thing, as it can be used with many other projects - I'm currently using it on my Rat Rig V-Core. A horns_duct_dimensions_v1.0.0.pdf file has been uploaded, containing...

# Horns Duct V2 - Layer Cooling ## Utilized In: - Unseenmaker's remix, available at https://www.thingiverse.com/thing:3924864 (check it out) - Small Footprint Titan Aero (https://www.thingiverse.com/thing:3600079) - Low-X Titan Aero...

Additionally, it features mounting points for a 40mm layer cooling blower-style fan. The specific fan used was chosen because it includes a 90-degree adapter that directs air into the ideal spot to cool prints. The included "BL Touch Mount" makes it...

Human: Sometimes, it's absolutely necessary to increase the tension of the stepper motor for the extruder, and in doing so, the motor may heat up stronger. To counteract this effect, I developed a housing that can be placed over the motor and...

A 40mm supportless fan mount is available for MendelMax and Prusa models, featuring directed cooling, which can be used in conjunction with a reinforced Prusa X carriage and slim LM8UU holder (http://www.thingiverse.com/thing:18657). ...You can also...

Hello, this device proves incredibly useful in cooling down the stepper motor when extruding within a sealed box. It's specifically designed to be used with my E3d V6 carrier only. ...By employing it, I've noticed a significant reduction of 15 degrees...

Main mods: * MKS Gen L controller board * Raspberry Pi 4 with Octoprint and Klipper * Klipper firmware * TMC2208 drivers * Zesty Nimble extruder * E3Dv6 hot end, soon to be replaced with a Mellow NF-Crazy (Slice Eng. ...Mosquito clone) * PrecisionPiezo...

This carriage also has mounting points for a 40mm Layer cooling blower style fan. I used the following because it comes with a 90-degree adapter that shoots the air into the perfect spot to cool your prints. <a...

I've got an E3D V6 Clone hot end on my A8 and I wanted to use a 40mm fan to cool down the heat sink. I also wanted to repurpose the stock 30mm fan as a parts cooler since I'm printing PETG and don't need a ton of cooling, so I decided to keep the hot...

This is a minimalist cooling sistem for the hot end. ...The air flow point directly to the noozle to avoid layer melting.

This design is primarily intended for use with a Slice Mosquito or compatible hot end. I have a Mellow NF-Crazy Magnum from Aliexpress, but it's also compatible with E3Dv6 and clones. It has been working great so far. Check the pictures for bridge...

With a laser cutter at my disposal, as well as access to a workshop in Mumbai that can shape acrylic, I took advantage of their capabilities to build this cooling fan for cooling PLA prints. It remains to be seen whether this effort will lead to...

A custom-designed fan system tailored specifically for the Titan Extruder, comprising a 40mm part cooling fan and an E3D heat sink integrated with a 30mm fan. ...The design is mirrored in its accompanying duplicate file.

Calibrating Heat Exchanger 40mm for E3D V6 Hotend.

I was determined to maintain the full z-height and utilize my 40mm Noctua fan for optimal cooling. Additionally, I wanted a part fan with a duct that completely surrounds the hot end. Lastly, I aimed to incorporate a fully enclosed filament path...