supportfan 40mm for extruder with layer cooling 3d models

... nuts for the back plate 7 - #6-32 x 1 in plus nuts for all other parts (As I'm based in the US, metric screws are expensive and hard to find. The #6 is just slightly larger than a 3mm screw, so m3's should be suitable for everyone else) 1 - 40mm fan

The front fan is a 24v 40mmx 10mm fan and the top two fans are 12v wired in series 40mm x 10mm fans. If you already have a BLTouch setup youll need to adjust the sensing points in the firmware because this will offset the BLTouch more than the normal...

This design takes a fresh approach to extending the Active Cooling Fan from thruit00 (http://www.thingiverse.com/thing:537918) to work seamlessly with the stock FFCP2016 side blower fan (http://www.thingiverse.com/thing:1746693). As I worked on...

A custom mount is designed to fit the Bigtreetech Skr V1.3 3D printer control board, destined for use in my DIY 3D printer project which will be released at a later time but should also work with other printers. The mounting holes are precisely...

I couldn't locate the authentic design file for the 20mm fan mount on the Prusa Nozzle MK2, so I was forced to create my own from scratch. ...To enhance print quality and speed, I designed a simple 40 mm fan mount that targets the tip of the nozzle with...

... ...I'll be using it in my DIY 3D printer that I'll be releasing in the future but it should work for other printers as well.The mounting holes are 86 and 70mm apart.For more info you can watch this video I made: https://youtu.be/Me80aXZixYg 

I snapped the original 30mm barrel on my Anet A8, so I upgraded to a brand-new 40mm barrel. ...Consequently, this is a revised version of the cooling duct that worked seamlessly with my old 30mm barrel.

Update 05-03-17: Fan Mount model revised to eliminate fan lag Dual 40mm Cooling Fan Ring designed specifically for E3D V6 Exruder Requires: 2x 40mm fans, 1x 30mm fan, 10x M3 x 16 screws 4x M3 x 8mm 2x M3 Nylock Nuts 2x M3 washers Print Settings...

When the cooling fan went bad on this printer I found out that it was using a 45mm blower fan for part cooling, which couldn't be found anywhere. ...I did have a bunch of standard 40mm fans so I whipped up this adapter in Fusion 360.

When the cooling fan failed on my printer, I discovered it relied on a 45mm blower fan for part cooling - a component that seemed impossible to find anywhere. ...Having a stash of standard 40mm fans at my disposal, I quickly turned to Fusion 360 and...

For the part cooling fan replacement with a 40mm fan, check out my other file https://www.thingiverse.com/thing:4753447 The nozzle cooling fan can also be replaced by inserting a 40mmX10mm fan into the right side of the module where the smaller fan...

For users who require even more effective cooling, a "2 FAN" version is available (two 40mm fans), which can be found in the file section. Feel free to suggest improvements and share your creations and photos! ... You can connect with me on social...

This is a remix from superpotatofudge's [CR-10 40mm Stock Hot End Cooling Duct](https://www.thingiverse.com/thing:2160958). I redesigned the thing with radii that match the Noctua NF-A4x20 fan. Also replaced the original hot end attachment with one...

... a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. ... It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the back-center. ... A M3-.50 nut is required.

For use with Takoto Hotends. ... Mounting & Duct for 40mm axial fan, using two M2.5 x 10 fasteners. Other variants available. ...

Extruder-Cover-Ender-3.zip Includes: * Clips-Ender-3.stl * Cooling-Ender-3.stl * Extruder-Cover-Ender-3.stl * Extruder-Cover-Ender-3-without-sensor.stl CABLE CHAIN FOR 3D PRINTER: https://cults3d.com/en/3d-model/tool/cable-chain-for-3d-printer...

This duct enhances the 40mm Fan Duct V3 from Ultibots, optimizing it for print-without-support ease and even cooling flow distribution across the gap width. It additionally directs airflow toward printed parts near the nozzle's end. The fan mount is...

Cooling duct layer for Anet A8. The compression cone directs and increases the air pressure in the nozzles that are oriented to the deposited material, so that it does not cool the extrusion nozzle but the layer of material. ... Designed specifically...

My trusty Prusa i3 steel printer was already equipped with Greg's extruder and an E3D V5 hotend, but it lacked that extra oomph from a layer fan. ...It was time to take matters into my own hands and create a solution that would breathe new life into my...

This is a compact 40mm fan cooling adapter engineered to perfectly fit 22.5mm Full Metal Hotends, ensuring optimal thermal management and reliable performance during even the most demanding printing sessions.

The creation is a 40mm fan attachment designed specifically for Kossel Mini with J-Head Hot-end. This innovative design splits airflow into two parts, with the top half cooling the PEEK component of the hot-end, while the bottom half channels air...

It securely mounts to the E3d Volcano hot end cooling fan shroud, expertly clears a Bondtech extruder and may also work flawlessly on your custom 3D printer. I precision-sized the holes for 4-40 x 3/8" socket head cap screws which function perfectly...

Since it utilizes an X-carriage setup, I replicated its duct attachment mechanism: https://www.thingiverse.com/thing:84345 You may need to fine-tune hole sizes by hand for a snugger fit, particularly on part three. To secure parts one and two, simply...

This is a mounting solution for a NEMA17 extruder's cooling fan, measuring 40mm in diameter. To create it, you'll need to print with either ABS or PLA using settings of 0.2mm layer thickness and 70% infill. A separate support structure isn't required...

Simple stepstick cooling tunnel for DUE3DOM LE board. ... Needed parts: 1x 40x40x10mm fan 4x M3x15mm screw

A simple 40mm cooling fan bracket for cooling steppers, etc. ... I had an issue where the extruder motor would get hot enough to soften the filament in the metal extruder, regardless what the stepper voltage was set to (and work!) So, a little fan keeps...

Constructed with an extra-large 10mm by 20mm recessed space, this component serves as part of a cooling mechanism for heat dissipation. It snugly connects to a lower duct for seamless integration. ...(Despite a crack in the picture due to filament...

The accessory is specifically designed for the Ender 3 and comparable models, attaching securely to the side of the standard extruder casing. ...Several similar designs are already available on Thingiverse, but this one raises the fan a notch higher,...

Compact Reality Ender 3 Extruder Protection (Cover) with Standard Cooling Locations and BL Touch Mount. A model without a sensor mount is also included for your convenience. The advantages of this design are numerous: Compactness makes it perfect...

However, it falls short in one crucial aspect - a suitable mount for a 40mm cooler is nowhere to be found. My revised version addresses this issue by incorporating a screw that keeps everything stable even at high speeds. Alternatively, the pin-based...