support free 3d printing

It's essential that the tissue had a melkoformatny print, or the fabric pattern may not match the image of the doll. Tilda is usually carried out in a compact size, so it's best that the fabric was not too big. Dolls Tilda are sewn two ways: hand...

Please be so kind as to leave a tip if you decide to print and install this and share your results. Advantages of this design: - Universal - Suitable for hotend and under bed installation - No loss of build volume in any direction - Easy...

Due to the adhesive discs on the wind turbines, a print bed with at least 210x210 mm is required. There are 5 different lids. With NabeTest you can adjust the bearing seat of the wind turbines with scaling in X and Y. The labyrinth ring is glued to...

When I built my dedicated printing room, I failed to notice that the switch for the overhead lights was located at the top of the rear wall, which is not very convenient. This design has 4 main parts: The Switch Plate mechanism, The Corner "Pulley",...

... screws from the PCB, make sure the PCB is in place, put the lid on top of the body, and tighten everything together with 4 M3x12mm screws. Contributions are appreciated - it took a lot of time to get the design made in Fusion360 and test prints.

The thing consists out of 2 parts that you need to print. In addition you will need: 1x compression spring, 1x M6 bolt, 1x M6 hex nut, optional 2x M6 washers and a gasket (20mm). Installation is straight forward, install the hex nut in the...

If you have SWU, you should print another one. The holder has indentations to facilitate tile draw. Still it is tough enough not to deflect or break. Note1: I keep Popular Places and Righteous Relics tokens in a textile bag - I think it is a better...

Generating Attributions log: [0] Thing Title : Cover for Flashlight [0] Thing URL : http://www.thingiverse.com/thing:882 [0] Thing Author : wizard23 [0] Thing Licence : Creative Commons - Attribution - Non-Commercial [1] Thing Title : Harmonic Drive...

Estoy seguro de que si se pusieran las pilas podrían volver a crecer mucho.-AUTO TRANSLATE TO ENGLISH-After 3 years of using my mobile charger (huawei P30 PRO) the connector had started to break slightly (surely my cat biting it and dragging on the...

Disclaimer: By purchasing this product, you can print and collect the pieces. This does not include a commercial license, if you want to sell them, you must contact with us to expand reproduction rights. Although this collectibles are inspired by an...

Print that inner panel whatever color you wish and use white LEDs to shine through, or any combination of plastic colors - LED colors, color shifting, or controllable I use two buck converters like intommy does, but with a slight difference. The...

So you have to print everything but only one BLTouch mount... All screw connections are designed for melt inserts. I used Ruthex but others should fit as well if they have similar dimensions. In total you need : 10 x M3 inserts (8 if you...

The printed gear wheel has a wide spot in the gears with a 3mm hole and space for a nut on the inside. To keep everything secure, I filed a matching flat spot on the rod where the gear fits. Assembly is relatively straightforward: 1. Check the...

eerything you need to play is included, it's an easy print for a game that you will play for days and days!!! hope you enjoy it!! Rules: in french sorry... (you can copy and translate!) Material list - 1 game box/stand - 1 game board - 4...

Preparation * Print the puzzle components * Have phones or tablets with the Aurasma app installed * Provide students with 20-25 minutes to solve the puzzle References The math involved in this puzzle is relatively simple, so no references are...

Recommended Material for printing: Sainsmart TPU @ 01.mm / 210°C/ 40mm/s / no retraction Update: You can now buy my Gatehunter pod combined with the LeDrone Club Pickle frame from...

Here is a bird's eye view from the top:A single pulley gets attached to the left wall bracket of your curtain rod. The left clamp gets attached to the first tab of your left side curtain. The right clamp gets attached to the first tab of...

Besides printed parts, you'll need to complete these hardware requirements: Lid: (Button Head Screws ONLY) Six M3 6mm or 8mm Button Head Screws Eight M4 8mm Button Head Screws Inside Box: All Boards: M3 4mm Button or Cap Head Screws Fans:...

I printed the coupling with TPU and fits onto the gear wheel of the stepper motor and onto the self-locking nut M8. The stepper motor probably comes from a Canon inkjet printer. ... Are needed: 1x stepper motor 35 mm SMJ35-4831-B or identical 3x...

I've split the provided top shell part into pieces that can be printed separately. The now separated flanged sun shields are inserted into the openings from the front side. They're glued together with the case and internal transparent neutral white...

Since my first-generation 2/3 plane connectors broke due to FDM layer separation issues, all the connectors in this series are printed so all connectors extend out on one plane, meaning that FDM printers are more than capable of building these very...

This print took me about 17hrs on my Creality CR6-SE as I wanted it to be super solid and smooth. This palette is made to fit a 3-layer storage container from walmart...

Now you can print everything required for installing landing gear on your Mini Talon easily. https://youtu.be/qJZGLSQbhl0 Parts Needed: - Landing gear kit from Banggood or any wire spring landing gear using M2 wire. - Used for front nose gear:...

// FISH FEEDER MINI BY FAU // Caricato su mini fish feeder il 29 marzo 2020 durante la quarantena per Covid-19 // Versione definitiva e attiva // 1 sola attivazione giornaliera data dalla luminosità della lampada accesa o spenta // dopo 10 minuti...

... or it can create a cone effect not allowing you to close the top. a little extra force may be required to pop the surround into the topBase. Commercial replication and production prohibited, selling files or prints without my consent is prohibited.

My version is intended for those who want to update their stock motherboard with a drop-in replacement such as the SKR Mini E3 or the Fysetc Cheetah so they won't need to print a new right case a second time. Instead of using TLSmoothers, I added...

Geoff Gregor's notes on his R2a modification state: "Summary: Nut pocket slightly bigger, screw head pocket much smaller, less damage, no more slop, screw stays aligned for happy printing (hopefully)." After struggling with a squeaking belt on my...

This set contains 5 heavily armoured Kingsguard Heavy Cavalry equipped with lances.  the Riders and Mounts are separate models for ease of printing and painting. Presupported files are included for each model in both STL format and LYS (Lychee...

To achieve this, you can adjust your printer using the following template: https://www.thingiverse.com/thing:5413456 It allows you to adjust the feed rate specific to your filament to obtain precision of the order of a hundredth of a millimeter,...

After printing the mount, you may need to widen the opening for the magnets with a 7mm drill - since the magnets I used are 7.1mm, they hold very well within the holes without any glue necessary. The bottom of the Sidewinder is made of steel while...