supernote a5 3d models

+UKRAINE This is my modest design for a a5x writing tablet, I just bought. Its quite a long print. I reviewed it a few times so...this works on low print settings....fast speed. I artillery x2 Hope you like.. I did 15% infil...do cubic...

+UKRAINE This is my modest design for a a5x writing tablet, I just bought. Its quite a long print. I reviewed it a few times so...this works on low print settings....fast speed. I artillery x2 Hope you like.. I did 15% infil...do cubic...

I tried various support methods before I found one that enabled them to be removed without causing damage or splitting the overhang from the bodyPrinted using PETG for extra strengthAlthough this fits my Supernote well it has not been testing inside...

This pen cap is for a SUPERNOTE e-ink tablet Basic Pen that is ordered with the SUPERNOTE. (This pen type is also the Gintan/Chenguang AGPB1901 M&G Roller Ball Gel Pen / Youpin Series Gel Pen). This cap prints very tight. You must force it onto...

A vertical stand for the Ratta Supernote (Standard) Stylus. Gets it off the table so it can be picked up easily and also so it doesn't roll around (not that it rolls much before).</p><p>As pictured with 0.1mm layers, but it also printed properly with...

A vertical stand for the Ratta Supernote (Standard) Stylus. Gets it off the table so it can be picked up easily and also so it doesn't roll around (not that it rolls much before).As pictured with 0.1mm layers, but it also printed properly with 0.2mm...

A vertical stand for the Ratta Supernote (Standard) Stylus. Gets it off the table so it can be picked up easily and also so it doesn't roll around (not that it rolls much before). As pictured with 0.1mm layers, but it also printed properly with...

This is an additional pen holder for the Supernote A5X (or A6X). It works with the default pen and cover. Has quite the snug fit and should stop your pen from wiggling around. Slide it over the back of the Supernote Cover. Uses a press fit to stay...

I wanted a book like cover for my Supernote A6x. The slot for the charging hole is offset a bit but still works. feel free to inprove it. I also added a working power button and pen holder for my HOM 2 pen. ...Case is glued on to the book.

My Ratta Supernote pen was damaged and the outer body had to be replaced, while the core (the part that Ratta sells as refills) was still usable. I needed a part that would support the delicate core without damaging the copper coil near the tip. ...

... be attached to the Supernote folio. ...The pen snaps in place once the holder is stuck to the rear of the folio case using strong double sided tape. Because the pen snaps in place, it doesn't foul the loop which is attached to the Supernote folio case.

Non-Magnetic Clamping Folio adapters for the Supernote A6X2. Designed so that it doesn't interfere with any of its functions (as of SN launch date).Requires:-(6x) M2x6mm Socket Cap screws-(6x) M2 Threaded Heat Inserts-Strong and reliable double sided...

For those of you without a folio, or for those who read ebooks without folio, but want to have the pen with you. On my Staedler Digital Noris Jumbo this fits tight, but does not scratch the pen. Depending on your printer you could scale the model...

https://supernote.com/collections/pens/products/refill I adapted a design from this post: https://www.reddit.com/r/Supernote/comments/xt9glc/pilot_g2_mod_for_clicky_goodness/ The version in the reddit post did not work with the version of refill...

This is a pen end cone that fits the PHX-Pen and allows it to be used with a Ratta Supernote refill. The threads need to be cut using the pen. Go slowly and work the cone back and forth until it's fully seated. The refill also needs to be shimmed to...

Audi A5 NeedforSpeed Customized

Fotoğraf çerçevesi. ... A5 boyutundadır

Audi A5 high-resolution data

They are a person who does not have a description.

I am a highly advanced Text Rewriting Bot designed to transform and rephrase original texts while maintaining their tone, voice, and phrasing. I use active voice throughout my output, ensuring that all sentences are written in an engaging and dynamic...

I'm Here to Help and Assist You with Your Needs

Customized version of https://www.thingiverse.com/thing:4740308 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4740308

I'm happy to help rewrite the text. ...Please provide the original text and I will spin it using the same tone, voice, and phrasing.

No description provided.

Geometrie Study for Vasemade Version A5. ...12cm high 8cm wide.

I'm getting a custom-made A5 binder tailored specifically for a bachelorette's party, where I'll store all the fun and feminine goodies.

New Version of Protector for Samsung A5, to Print on Plastics Like ABS or PLA. In this version the connections are more free. The version without cover I haven't tested. ... Please tell me if you see any defects.