superman 3d model

As always, the .blend file and pre-supported .obj (the one that I used to print it on my Prusa mk3 with a .25 mm nozzle) for this model are available to my patrons at https://patreon.com/VirtuallyJason. If you appreciate my work and have a few...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

Knob channel.stl - channel knob, for 16 position rotary encoder, model unknown, mine was from professional 16-ch radio. 7. Antenna.stl - old-style, PRR mock antenna. 8. Antenna New.stl - new style, EZ-PRR mock antenna. 9. PTT Lemo Single.stl - PTT...

Since the build volume on the Prusas is relatively limited i decided to maximize the footprint of the stand for stability. As for the height, the 2 piece construction while theoretically takes more time to print, there is no need for support for the...

The original interior geometry from the Prusa filament sensor has been incorporated into this design, sourced from Prusa's models. The pinda is in the same location as on the original. The nozzle in this new design sits 10mm further forward along the...

If they are different, please update the Fusion 360 model and re-generate the toolpaths. Also, if you plan on using different tools for the above operations, make sure you update the tools (and associated feeds and speeds) and regenerate the tool...

- You can find a somewhat more detailed list of supplies in my Instructable at https://www.instructables.com/Kissing-the-Frog-V20-Back-Horn-Bluetooth-Speaker-F/ Basically any combination will do (as long as the driver is 3.3" or smaller so it fits...

Check out the Raspberry Pi 3B+ here: https://www.raspberrypi.org/products/raspberry-pi-3-model-b-plus/ The controls are simple but there's enough buttons for most games. D pad for direction control and 4 front buttons provide your basic SNES type...

Additional mounting types are avaiable for this model.This explosion proof LED light fixture is paint spray booth listed, IP67 rated, dust-proof, and protected against high pressure jets and temporary submersion. The cast aluminum body and LED lamp...

Depending on the figurine put on top of the box a different playlist ist played, currently mostly kids audio books and a spotify music playlist.All in all a very cool project that i hope to expand when my son grows older.ElectronicsPhonieboxRaspberry...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

...Thank you! Change Log:25AUG2022 — Added model and print files of a 3-point version of the modified MINI-minda-holder for using the SPA with Sparkyman987's Fan Spacer Mod.11NOV2023 — Added .step file of the SPA for MINI/MINI+; added remix description.

I got a package of 5 and when I opened them I found that the design had changed slightly and the material they used on the newer models was slightly thinner. The original clips were therefore a little sloppy. I adjusted the clips to fit the newer...

A round-pole design makes the assembly easier to handle and transport compared to square-shaped models.A horizontal T-mount platform is provided at the top of the tower for mounting customer-provided equipment. The tripod features a rotatable head...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

It is essentially based on my first design.If you don't have an AC Infinity T8 or don't want to spent 120 bucks on one just to disassemble it, check out this simpler and cheaper...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

 February 17th, 2022Parts Revised:Wire GuideThere was an error in the model that I didn't catch.  Part of the base wasn't extruded in Fusion360.  Version 1.3 is still usable, but it's not what I had intended, so here is version 1.4 of...

Four screws for every corner and 8 screws for every side.[blue] NO acrylic glass holder at the side where the hinge mechanisms are located!From this on the “Front” is where the hinges are.[green] At the location of the green circle you can drill a...

rice or sand.Glue if the press fits are not tight enough Testing tolerancesStart by printing the models press_tolerance_test and rotation_tolerance_test from the folder Common parts.Press fit toleranceUse the press fit test to decide which press...

Or rather, it's a scale model of what that house looked like fifteen or twenty years ago. The wrecked version is closer to how it looks now that it's been abandoned for the better part of two decades. The tweakers have had a field day with this...

The use of simple metal parts in combination with printed components holds a lot of potential for the future; FreeMenDontAsk is already working on other handgun models. Even outside of gun making, this could be useful for a wide array of printed...

We are modelling the *BELT* tooth here, not the tooth on the pulley. Increasing the number will *decrease* the pulley tooth size. Increasing the tooth width will also scale proportionately the tooth depth, to maintain the shape of the tooth, and...

You may have to do some light cleanup, but the fit of the parts should be snug enough to hand press together with no wobble. IOMarms STL- These arms are taken directly from the original wood designs and are generally sized for an IOM, but are not for...

The design is a complete rework of my older oscillating fan model.It uses a common 130 size brushed hobby motor and incorporates an 18650 battery in its base for completely portable operation. Compared to the older design, the new version has...

Model says 119mm, which would be close.???---------------------------------------------------------------------------------------------------------Printed Parts: Base:___________________Placeholder____________________This is the base of the...

It deviates a bit of what I usually call an "sci-fi astronomical object", because it's an in-spacecraft transport vehicle. I made this model available in 4 scales. I left the model in "halves" that I consider the best way to print it, of course, with...

By doing so, I can now get more of the STLs to show up in 3D view on this site. The updated files have 10-18-23 dates and are renamed with "-remake" or "-k". 10-10-23 Update: Two items - Assembly Hints and Images added as a new section, and an...

If you don't own a 3D printer but have seen this blank somewhere else and want to use it, I recommend just asking in a furry group chat on a platform of your choice. Many furries are also tinkerers and will print this for little money.</p><p>The base...

I also added a version of the female parts with a tolerance of 0.2mm for those who have well tuned 3D printers (see below). To know more about your Printer tolerance, don't hesitate to have a look at <strong>Maker's Muse</strong>'s videos on the...