sup adapter 3d models

This stand-up paddleboard is constructed using the cedar strip technique, and comes with detailed cross-section drawings for your convenience. ...Simply print and cut out these patterns to create the mold for your project.

Remix of the pretty cool tube holder for the low pressure Decathlon pump from richardqj (https://www.thingiverse.com/thing:4900399), licensed under the Creative Commons - Attribution license. ...The clamp has been adjusted because the diameter of the...

A silencer for inflatable stand-up paddleboards Mutes the noise when deflating the board - no loud bang that hurts your ears. With an additional towel over the silencer, you can hardly hear a sound. The venting time is about half a minute -...

It is designed to be easily printed with filament, but if you have access to a resin printer you will be able to notice the details in the character The character moves from side to side because of the spinning of the wheels. All the wheels turn.

Pendural

Insert the car valve into the opening and secure it by tightening the two pre-assembled components. ...Next, apply a firm grasp to finalize the installation.

I'm sorry, I don't have a description of who that is.

These parts must be made from ABS and PETG without needing support.

[SketchUp Entities] 152 Groups / 37 Instances / 62642 Faces / 9 Materials

Printer Replacement Part T100, 500x500 Printer.

Handle for Stand up paddle, made for a Select Session paddle (29mm inner diameter). Not printed yet. designed to be printed without supports : just a brim ! ... will update as soon as ready

I use my straps often and need them to be easily accessible and always ready to use. This simple tool is printed in about 1.5 hours and can be used wall-mounted or by itself on the ground. This tool is made for 25mm straps.Pro tip: Use 3 walls, 0...

These parts must be made of ABS and PETG, without the need for support. ...Note that there are two pieces.

Tail wing designed to complement Dinceraydin Front wing, having created two front wings I determined it was time to design a matching rear wing. The resulting back wing features the same anhedral angle and similar outline as its counterpart, boasting...

I tried the great design of the [itiwit long fin](https://www.thingiverse.com/thing:5482004) from [hungryharris](https://www.thingiverse.com/hungryharris/) for my Decathlon Itiwit X100 kayak. Because I found some shortcomings in the model I decided...

I wanted to be able to take my iRocker Cruiser down shallow rivers without the worry of smashing up or losing the supplied rigid fins as well as reducing the likelihood of performing a surprise superman off my board. iRocker uses a proprietary fin...

Using a portable compressor such as the Tmax 8072601, people can easily inflate their stand-up paddleboard.

Ich konstruierte den Adapter von Boston-Ventil auf Düse, um die Luftmatratze meiner Frau mit meiner SUP-Pumpe aufpumpen zu können, um nicht noch eine weitere Pumpe mit schleppen zu müssen I designed the Boston-Valve to Nozzle adapter to inflate my...

This adapter is engineered to add a secure mounting system on the backside of this widely available and affordable tripod mount. ...It features a standard 1/4-20 UNC camera thread for easy attachment.

Bigger Braking Disc Adapter for Brembo Brake

This device, referred to as an adapter adapter, successfully enables a typical compact flash adapter to be fully compatible with the 2.5" form factor. ...By doing so, it effectively adapts the adapter to seamlessly fit within a standard 2.5" hard drive...

You will need to print (in PETG or ABS): 1 x tank_adapter 1 x tank_adapter_nut and (in TPU): 1 x tank_adapter_seal The tank adapter and nut are best printed in PETG. It has excellent layer adhesion, durability, and heat tolerance. ABS can also be...

I had to go down a river with low water so I removed the center fin (my paddleboard has 2 shorter fins also) but the directional stability was terrible. This adds a fin which is half the height (you can get more clearance by shifting weight forward...

Needed a way to bring a redbull and a water bottle on a Stand Up Paddle board . Small support is 58.5mm in ID , perfect for those High redbull can. ...The bigger support is 78.5mm ID , perfect for almost all water bottle ( nalgene , brita , bike bottle...

I designed a replacement fin for a friend's paddle board.  The root of the fin is thicker than the original so it should be stronger. ... We tested it over the weekend and it performs well.0.6mm nozzle, 0.3mm layer, PETG, Sovol SV01

Three-dimensional model generated using 3DF Zephyr photogrammetry software, processing 586 images.

The person speaking was a human being, an individual with thoughts and feelings.

Print according to the description of the extruder set.

Центральный плавник для сапа с специфическим креплением, как называется такой стандарт крепления найти не смог, отлично стабилизирует Оптимизирован для печати без поддержек. ...Я печатал из petg с заполнением 100% Толщина плавника 3мм возможно...

I just increased stabilty by filling the lower part - and added the slide in mount, as my first printed version (original) broke on tightening the screw