sunhokey i4 bltouch 3 1 marlin 1 1 9 mks base v1 6 firmware by 3d models

The prime link 6_3_1 is represented in the given model, tied within a constant-radius tube and tightened. The thin version has reduced tube size to enhance visibility of crossings. Conversely, the thick version showcases the full scale tube. These...

Lock the beads in place with 6 3mm bolts. Getting the tyres to go in is a wee bit tricky, but they hold nice and snug. :-) Print them on 100% infill to make them as strong as possible. ...The pieces go flat on the ground facing up, print the beads...

This case fits the ENDER 3 PRO to install the MKS Robin Nano v3.1 with Flash drive. Uses Stock 4010 case fan I made a couple changes, most obvious is the front to allow the mks board to work. Other changes i made are, .7mm bigger opening for the...

Bolt Self-Taped V1.6.1 Please scale as needed, thanks. Visit us at: Rixtronix LAB Channel https://www.youtube.com/channel/UC89se0BZ2oGeqN5jNbDAyQQ Need a reliable power supply? Check out these low-ESR capacitors: Motherboard Capacitors 1000uF 16V...

Materials: 4x M3 Heat Insert 2x M3 Nuts 2x M3x10mm Screws 2x M3x5mm Screws (Rest is used from stock toolhead) V1.1 Changes: - Added grooves to belt grip for less slipping on belt - Changed heat insert hole chamber to slot in heat inserts easier -...

Note: This is version 1.4.1RC24m4, firmware for my X5SA Pro, and it works perfectly fine. I will not be held responsible if it breaks yours. To use this software, unpack it from the folder and save it to your SD card. Next, insert the SD card into...

Marlin 2.0.7 compiled to use BLTouch for z-axis (in the plate centre point) homing and ABL. ... Speaker is also disabled as the beeps annoy me :D

The length should be perfect for the bltouch 3.1 ,but if it's too long you can always file the bottom end a bit. The remover is to be used if you need to remove the bltouch from the mount. This way you don't damage the probing needle accidentally. If...

6 piece set of Graveyard fun.  2 32mm bases, 2 Mausoleums, and 2 Gravestones. 

The Trinamic driver is wired according to "myseg": https://github.com/MarlinFirmware/Marlin/issues/12632#issuecomment-454149317 and https://github.com/myseg/MarlinFW_SKR1.1_SD_LCD Yes, CS and EN on the same pin seems strange - but that's exactly how...

... 40x40x10, specifically tailored for the Sunhokey extruder's unique specifications. ...This innovative 2-in-1 fan duct is engineered to freely rotate around its axis, allowing users to easily inspect and monitor the printing process in real-time.

They exhibit a wide range of emotions, thoughts, and behaviors that are influenced by their environment, experiences, and genetics. Humans have an incredible capacity for learning, adaptation, and innovation, which has enabled them to thrive in...

1/6 female half bust base stand

1/6 female half bust base stand

1/6 female half bust base stand

I designed this adaptor for my ender 6 to add and Orbiter v1. This is designed for the orbiter with the v6 heatbreak used as a filament guide. It bolts to the holes meant for the factory strain relief. I added a strain relief spire with and hole...

I'm attaching a mounting plate to my RAMPS board that came with the Hictop 3DP-12 (MKS 1.3). I needed something straightforward without any specialized brackets for extrusion, and this is working out perfectly so far. ...It's currently holding my ramps...

A custom plate is designed to hold an SKR 1.3 motherboard, replacing the MKS Robin Mini on the Flsun QQ-S printer. ...Some fine-tuning with a Dremel tool is required to free up space for the SD card and USB port connections.

This DIY solution keeps cables organized when installing an MKS-GEN 1.4 board on the Ender 3, specifically designed for use with the case found at Thingiverse (https://www.thingiverse.com/thing:1795015) and Tennisball-feets available at...

Box MKS Gen 1.4 for Ender 3, you'll need a fan of 80 mm thickness otherwise it will touch on the bed adjustment, also needed are four m3 self-tapping screws eight mm long to fix the sheda, two m4 nuts that must be embedded in the covers in their...

# 2020 Case for an MKS GEN L > And probably SKR 1.3 (as it has almost the same dimensions) Please consider TIPPING me if you like this or my [other designs](http://www.thingiverse.com/mcabra/designs) - It'll help me make more stuff and get some money...

This is a custom-cut acrylic case designed specifically for the MKS SBASE v1.3, featuring an integrated active cooling system powered by a 40x40x20 mm fan mounted on top. ...Crafted from sturdy 3mm plates, this rugged enclosure ensures optimal airflow...

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=167866 Instructions Using the following settings: plate width: 70 inches build plate selection: Standard motor designation: Motor No.6 line one display text:

I made this bracket to attach an MKS base 1.5 to my AnyCubic Kossel Linear Plus, but it will fit any printer with a 2020 extrusion system. I created it because I dislike the Trigorilla board that comes standard on the Kossel. To print in ABS, use a...

... the radiator grille. ...7 and 5 part grille. Protected against theft. The base is printed in 2 colors (Pause at height). The letters are separate and then glued. The package includes all parts. ...Required screw sizes: 2 pcs M5x40mm 2 washers 2 nuts

... due to its unique and intriguing properties. ...This particular knot is characterized by its twisted and curved shape, resembling a doughnut-like structure with a twist. ...It is often depicted as a closed curve embedded in three-dimensional space.

Case for MKS Gen 1.4 Board Demands an Eighty by Eighty Fan Requirement.

The MKS Gen 1.4 board stretches significantly beyond the stock Ender 3 board, preventing it from fitting snugly into the stock enclosure. The enclosure protrudes slightly forward but positions the standoffs accurately to attach the MKS board...

MKS Gen 1.4 Box with 60mm Fan Mount

MKS_Gen_1.4_Box To install on profile 2020