suncast hosemobile parts 3d models

Modelled after parts from a Suncast JSF175 Hosemobile Reel Cart. ## Additional Parts Requires a retainer clip for attachment to the male section. I re-used my existing clip, but it available for printing by engineered16 here: ...

Personal attempt of Suncast Easy Bolt

Suncast Slatwall Peg hook. ... Added both ths single and double wide

I needed a tool to install the Suncast easybolts, its a offset hex wrench. ... .25" on one end and .3" on the sides.

... high infills. So, I decided to utilize a metal bolt at an angle that would fit into the slat wall perfectly. The Suncast slat wall sections which are sold by Home Depot and other home improvement stores were designed specifically for this system.

Replacement or accessory bolt for Suncast garden sheds. The thread is a very uncommon size (9/16"-10), making it difficult to source without purchasing from the manufacturer. ...These are a very sturdy and affordable option if you have access to a 3D...

... size using threonin and attached a head along with a hex hole to match my shed's plastic screws perfectly. ...I printed this part using 100% infill PLA to test its durability and longevity, now it remains to be seen just how well it holds up over time.

Bolt for Suncast Shed with a socket for a 3/8 allen wrench.

To upgrade your equipment, install a versatile attachment that takes the place of the standard side hose connector on the reel. ...For optimal performance, apply a thin layer of silicone grease to the inner surface of the large-end fitting, then secure...

Stainless Steel Phillips Pan Head Sheet Metal Screw (25-Pack):https://www.homedepot.com/p/Everbilt-10-x-3-4-in-Stainless-Steel-Phillips-Pan-Head-Sheet-Metal-Screw-25-Pack-800202/204275122 Suncast Vertical Shed...

I needed bins on my Suncast slat wall system, so I checked out https://www.suncast.com/sw04.html Many of the hangers required screws into the slat board; that was not flexible enough for me. To achieve my goal, I designed a bin holder to hold the...

See print settings note.* The [Suncast 47 Gallon Patio Storage and Prep Station](https://www.suncast.com/patio-storage-and-prep-station.html) comes with a utensil hook bar that doesn't fit some of my favorite utensils. This is a drop-in replacement...

... It's designed specifically for Suncast slat wall sections sold at Home Depot and other home improvement stores. To print this custom fit cup successfully: Enable Raft On Enable Supports Set Infill: 35% Recommended for 'pegs' stability.

I used two parts printed at 35mm (3.5x) and one at 10mm to fit into three recesses in the header and support my jump-start battery pack (~20 lbs). Design Details: Autodesk Fusion 360 was used to design this hook, which has an ID of approximately...

The Suncast 47 Gallon Patio Storage and Prep Station comes with a utensil hook bar that doesn't fit some of my favorite utensils. This is a drop-in replacement with smaller pegs, so that I can hang my tongs on it.</p><p>It's also useful if you want...

A hanger or hook for the end walls of a Suncast Garden shed. Hanger attaches to the underside of the end header on the shed as shown in the photos above. To attach, slide into the recess under the header then onto the lip sticking out. Hanger can...

You have done it well by saying "to fix a broken valve handle" instead of "Broke the valve handle on", and "I designed a more robust replacement part" instead of "Created this sturdier version to replace it." But you could have used even fewer words:...

Broke the valve handle on my Suncast Hose Reel RSH125. ...Created this sturdier version to replace it.

https://www.homedepot.com/p/Suncast-225-ft-Swivel-Smart-Trak-Hose-Hideaway-CPLSSM200B/205600965 After getting it hooked up and reeling in my 125 feet of heavy rubber hose I noticed my palm skin was getting hot on the handle from friction because the...

https://www.homedepot.com/p/Suncast-225-ft-Swivel-Smart-Trak-Hose-Hideaway-CPLSSM200B/205600965 After getting it hooked up and reeling in my 125 feet of heavy rubber hose, I noticed that my palm skin was getting hot on the handle from friction...

I fabricated these replacements parts from PLA and PETG. Both seem to work well. The PLA deformed more over time than the PETG. I do suggest printing the screw sideways with support to give it more strength along the shaft. The original hex...

I fabricated these replacements parts from PLA and PETG. Both seem to work well. The PLA deformed more over time than the PETG. I do suggest printing the screw sideways with support to give it more strength along the shaft. The original hex tool is...

Photos included so you can see the original part i replaced, the replacement, and what it looks like installed. I'm using Prusa Slicer and I am generally a fan of leaving infill at 20% but increasing the number of perimeters to 5. ... This seems to...

My Suncast Hose Mobile retainer clip failed me due to excessive water pressure, constantly popping off. Its original design featured a chamfer that only added to its vulnerability. To rectify this issue, I redesigned and streamlined the clip for...

I had one end of one of the gas struts that hold the lid open break off of my Suncast BMS4700 horizontal shed when a wind storm flipped it. Rather than replacing the whole strut, I was able to print a new end. Use at your own risk, gas struts are...

My retainer clip on my Suncast Hose Mobile failed and would keep popping off with the water pressure. The original clip has a chamfer to it that makes it even weaker. I recreated it and simplified it a bit. ...I printed it in PLA, but ABS would be ideal...

You may want to modify the part to use what you already have instead of buying specific parts. The pipe is 3/4" inside diameter and 1" outside diameter PVC pipe. I didn't measure the length of the original handle; I just held a piece of pipe next to...

I designed a J hook to secure this shed screw, marking my first creation and a respectable start. The design was inspired by a model found on Thingiverse, specifically thing:858067. ...To print the hook, I used a 30% infill setting, which didn't offer...

parts

important part