summit livescope pole 3d models
18067 3d models found related to summit livescope pole.thingiverse
These cable clips are sized accordingly to fit the pole that I use for my Livescope Ice Fishing Bundle (Summit Fishing Equipment). Small, medium, and large clips to fit each section of the pole. The clips also feature a tab that locks the clip into...
thingiverse
This is a tripod design for a extendable paint pole, to use for Garmin Livescope transducer ice fishing. Should fit any pole with a 1.25" OD. Connected with 1/4-20 1.25" round head screw & nylon locking nut. ... Pole I used:...
thingiverse
This is a custom Livescope pole that I designed and printed. This is the first version and may be changed as I keep using it. The pole I designed it for is listed below from Amazon. It extends from 1.5-3’. I’m from Se MN and we don’t get very thick...
thingiverse
Summit Shuttle battery guides made taller and additional for the sides. ... https://www.tinkercad.com/things/lNEoj3Gdmg7
thingiverse
I created this so I could use my Livescope System Ice Fishing without having to spend $150 on one from a store. The pole is one half of a kayak paddle. The paddle is 30mm in diameter. The adapter was designed to slide over the smaller end of the...
thingiverse
This a remix of JacobAndrew version but has a threaded mount for the same pole he has listed along with other minor adjustments as well as extensions for thicker ice. I will add newer versions of the files as needed. ... Pole-...
thingiverse
No modification only save it as .3mf to help people print it :) all the credit to blizzard317
thingiverse
Designed to attach to a pole mount, this particular model accommodates a 28mm pole, which I built from an anodized aluminum telescoping pool cleaner pole. This mount comes with the knob design to tighten and adjust the angle as needed. ...It uses a...
thingiverse
Top mounted mount and cable saver for Garmin Livescope that will do forward and down view without the use of a knob to untighten. ... Simple put together pieces with a bold and a flexible rubber washer or spring so it's tight enough to hold angle but...
thingiverse
... the part dense it is printed with 6 shells. Print temp was 245, bed @ 110 degrees C. This is such a simple part allowing for many other print options. Too bad Garmin doesn't include this wedge for zero degree pole mounting with the Livescope kit.
thingiverse
Protective cover for expensive Livescope transducer. ...
thingiverse
I adjusted the Livescope_Mount_v4.stl to include a cap (Livescope_Mount_Cap_v1.stl). I had an issue with the bolt that mounts the actual transducer on would loosen over time. I was worried it would be at the bottom of the lake eventually so...
thingiverse
This part is for the Garmin Livescope transducer. This part should help prevent the transducer cable from cracking/breaking when it meets the transducer. ... Additional Items needed to attach part to transducer: -4 Stainless M4-.70x12 screws
thingiverse
This is a custom arrow designed specifically for my DIY transducer pole, which I use in conjunction with my Garmin Livescope. The arrow perfectly fits into standard 3/4 inch PVC fittings, making it easy to attach and detach as needed. As shown, the...
thingiverse
Mount the new Garmin Livescope transducer in perspective mode with precision and ease. Printed with PETG or ABS yields exceptional results, while nylon, although suitable, proves slightly too pliable for optimal performance. ...Savor the experience!
thingiverse
This is a clip used to secure the Garmin Livescope transducer cable to attach to my homemade mount. Was using electrical tape but did not like it when I spun the transducer head around too far. Was concerned about binding the cable too much. Made...
thingiverse
Spiriting Adventure Through Turbulent Climb As One Creates Ascent of Epic Proportions With My Most Inspiring Mantra. ...Crafted in Visual Wonder CINEMA 4D.
sketchfab
This is Donner Summit near Truckee, California. ...I captured it using Photoscan Pro with more than 500 aerial shots taken directly from my drone.
thingiverse
A customized version of the "Summit" design can be created from thingiverse's model with ID 52734, using the Customizer tool (http://www.thingiverse.com/apps/customizer/run?thing_id=52734). ...To do this, select the following options: stick width of 8;...
cults3d
... probe. ... 3 versions of the bracket that fits on a 20mm diameter, 25mm or 30mm tube. I can offer other version for other diameter tube on request. For the assembly you will need: 4 M6 nuts 1 M8 nut 4 screws M6x25 (supplied with the Livescope)