subaru outback phone holder 3d models

These are the files needed to make a bracket to add LED fog lights on a 2013-2019 Subaru Outback. A video tutorial can be viewed at this link. ... https://youtu.be/wfj0wofthn0

This is a substitute hood prop clip designed specifically for the Subaru Impreza Outback Sport model year 2007. ...The part is printed with a minimal amount of support material, only 3%.

Replacement clip (female) for the all-weather covering in a Subaru Outback (this was specifically a 2011). The male portion of the clip that has a screw-like portion was intact, but the female sides had broken. Metric units used. ...The clip should...

This is also uploaded on PrusaPrinters at https://www.prusaprinters.org/prints/86524-subaru-legacy-outback-2011-4th-gen-trunk-pins ## Notes on the source file The source file is attached. It uses FreeCAD Link branch daily (downloads from...

These are replacement clips for the [rear seat back...

Subaru strut spacers

Designed for use with aftermarket stereos in 2015-2017 Subaru Legacy and Outback models to replace the factory Aux and USB module ([Subaru part # 86257AL00A](https://parts.subaru.com/p/60018578/86257AL00A.html)) The dimensions of the factory part are...

Use this false bottom to hide important belongings in the center console of a 6th generation Subaru Outback. Provides an unsuspecting 12mm of clearance over items like cash, credit cards, or anything else you might want to keep out of sight. ...

This is a center console mount for your Microsoft Lumia 950 or other mobile phones of similar size. The mount uses friction to slide into the slot between the factory stereo and the center stack. Since this mount rotates, some assembly is required. A...

Console tray for 4th Generation (2010-2017) Subaru Outback. I modeled the original part, but without the blank for the ejector switch (or whatever the higher trim level comes with). Original tray was sized to fit 2009 cell phones and mine was always...

It might fit other cars, but the one it fits for sure is Subaru Outback 2005 with the detachable AL-KO tow bar. Part numbers, that might help identify the correct device: L101EAG971 EAG071 The designed is parametric and can be tuned with...

Pins for the side trays below the "floor" of the trunk on a Subaru Legacy Outback 2011 (4th gen).Tested on a European Outback 2011 2.0D (diesel engine) model. I assume it is the same across all variants of the same year at least though.Notes on...

Rear Door Speaker Mount Spacer For Subaru Legacy 3rd Gen

Subaru Legacy 3rd Gen Rear Door Speaker Mount Spacer

Adapter for Subaru Outback IV with integrated (foldable) crossbars. To be able to mount Thule ski rack, I've created adapter which fits onto crossbars and you can fit Thule ski rack on.Due to curved aero shape of the crossbars, left and right parts...

I've Designed a Customized Trash Can Compartment and Swiffer Slot for My Outback Vehicle, Utilizing Widely Available Poop Bags. It's Recommended to Use PETG on Very Hot Days Due to Its Durability. ...A Secure Kinetic Panel is Also Included for Added...

... works flawlessly! You can even charge your phone while it's secured in this holder. ...I did use 3M white Command Adhesive strips to attach the cradle securely to both the holder and the car - the white ones are necessary, not the thin clear ones.

I have bought white/yellow WY21W switchbacks for DRL on my 06 Outback. I do not like to see connector unprotected or covered by electrical tape. So I made simple cover that also hold resistor (M3 screw) and could by mounted with M6 bolt or ziptie. On...

I have bought white/yellow WY21W switchbacks for DRL on my 06 Outback. I do not like to see connector unprotected or covered by electrical tape. So I made simple cover that also hold resistor (M3 screw) and could by mounted with M6 bolt or ziptie. On...

Subaru owner attaches phone to interior trim using adjustable arm and 3M adhesive strip.

always had a toy on the empty space and hated having to plug in the phone and randomly placing phone anywhere it fit, decided to look into phone carrier and then decided to go to AliExpress and get a wireless charger link below 5/6 - updated, removed...

... than the portion of the cord cuttout that is paralell to the build plate. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: Yes Resolution: .2 Infill: 20% Filament: Overture PETG Black Category: Mobile Phone

... else. Works like a charm! You can even charge the phone with it in this cradle. ...I did use some 3M white Command Adhesive strips to attach to the back of this thing and to the car, the white ones are needed NOT the very thin clear ones.

The slanted back portion shouldn't need supports other than the portion of the cord cuttout that is paralell to the build plate. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: Yes Resolution: .2 Infill: 20%...

I tinkered with the cup holder and expanded to 105% so it would fit my 2013 Outback and hold my Nathan Big Shot 40 oz. bottle. I added two differently-sized slots for cup handles as well as a couple holes to reduce the amount of filament needed to...

Detailed high-resolution model created by the skilled team at SQUIR. Rendering this scene in 3dsmax using VRAY is a breeze, as it was successfully rendered in 3dsmax 2015 with vray3.20. A rendering setup including lightning, materials, and...

High detailed model created by SQUIR team.

High detailed model created by SQUIR team.

The 3D model is an accurate replication of a real car, measured in actual units and closely resembling the original. Formats include *.max for 3ds Max 2008 scanline and vray, *.fbx, *.obj, *.3ds, *.mb, *.lwo, and *.c4d. The tire texture is not...

The 3D model was created on real car base. It’s created accurately, in real units of measurement, qualitatively and maximally close to the original.Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx (Multi Format) -...