sub ghz 3d models

This is a model of an Amphenol RF TNC Coaxial Bulkhead Vertical PCB Connector rated to 11 GHz (p/n : 122440).

This is a model of a 50 ohm Rosenberger 4-hole Bulkhead SMA connector (p/n : 32K421-200E3) that is used for up to 18 GHz.

This is a model of a Microwave Technologies (MWT) 20 GHz rated and 26 GHz capable (at the wafer level) (K-band) Metal Semiconductor Field-Effect Transistor (MeSFET) in a package 73 case (0.073") ; part number MWT-773 and is based upon the MWT-7 IC...

============================================= Military Mini Sub =============================================

D-SUB 9pin housing.

Realacc 5.8 Ghz 10dbi Antenna Guard Protection Cover Use a zip tie to secure both parts together. ... Print Settings Printer: Elegoo Rafts: ...

The text describes a prototype of a Sanav gefn-101 PIFA antenna, which has a gain of 3.97 dBi and a low VSWR (less than 1.7) at 2.450 GHz frequency.

The Sanav gefn-102 PIFA antenna has an impressive gain of 0.97 dBi, optimally functioning at 2.450 GHz and featuring a VSWR of less than 2.2.

The AntenneFPV Heliaxial antenna, designed for 5.8 GHz receivers with 5 turns and a diameter of 16 mm, features exterior solder connections. ...A Tarot F680 drone test video showcases its performance; view it here: http://youtu.be/eohLwvozBHo

This is a model that I created of a Linx Technologies 2.4 GHz High Gain Whip Antenna. It has a gain of 7dBi (5x) , which is pretty good for an omnidirectional antenna. ...It uses a N-type coax connector.

This is a model of a Tyco Electronics (TE) / Axicom 3 GHz RF SMT DPDT Relay that is available in latching and non-latching versions. ...It has a response time typically of 3 milliseconds, but a maximum of 5 milliseconds.

This is a 18-element log periodic antenna that I modeled. ...The elements still need tuning, however it is for wideband operation from 800 MHz ~ 6 GHz with a SMA coax connector.

This is a model of a California Eastern Labs (CEL - now owned by Renesas) 20 GHz rated and up to 24 GHz capable (K-band) GaAs Low Noise Metal Semiconductor Field-Effect Transistor (MeSFET) part number CE3520K3.A MeSFET is similar to a JFET in that...

This is a low cost Orthoginal Dual BiQuad (90 degrees out of phase) 2.4 GHz omnidirectional antenna that I modeled after a paper titled "Omnidirectional Biquad Omni-Antenna for 2.4 GHz Wireless Link Application" by Kalina Kalinovska and Peter Z. -...

This is an Amateur Radio Earth-Moon-Earth (EME) 10.368 GHz (3cm) IEEE X-band Septum Feed Antenna Aperture with the optional counter-bore 'Choke Horn' that was designed by OK1DFC (http://www.ok1dfc.com/eme/emeweb.htm#UNITS)For more information on the...

sub zero mortal kombat bust

50 PIN D-SUB DDM50S332N

D-sub 9 pin female

Keltec SUB 2000 dust cover

Keltec SUB 2000 dust cover

50 pin D sub connector

... a 1/4 wavelength of the frequency of interest. ...The starting frequency is 4.2 GHz and can go up to the maximum rating of this connector at 18 GHz (-3 dB) with a length of 1.67 cm (full wavelength). ...Note this does not include material thickness !

The starting frequency of the center conductor (determined by 1/4 wavelength length) is 4.2 GHz and can go up to the maximum rating of this connector at 18 GHz (-3 dB) with a length of 1.67 cm (full wavelength). ...Note this does not include material...

The starting frequency of the center conductor (determined by 1/4 wavelength length) is 4.2 GHz and can go up to the maximum rating of this connector at 18 GHz (-3 dB) with a length of 1.67 cm (full wavelength). ...Note this does not include material...

This connector is a 'jack' meaning that it has a female pin and is movable, unlike a socket which is typically stationary.A SO-239 UHF connector is only good to 50 MHz and this connector is good to 2.5 GHz so it has 50x the bandwidth (see...

... connection. ...The parabolic reflector is 12", the hyperbolic reflector is ~ 2.2", and the feed horn is ~ 0.25" IDReference (https://www.sagemillimeter.com/45-dbi-gain-92-to-96-ghz-12-reflector-diameter-wr-10-waveguide-w-band-cassegrain-antenna/)

This is a model that I created of a RF Beam 24 GHz K-LCx (all KLC1a and KLC2 models) RADAR Transceiver that can be used for self-driving vehicles, traffic control, and security.These models have a range of 12 meters.For more information see...

I designed this RF Beam 24 GHz K-LCx (all KLC1a and KLC2 models) RADAR Transceiver model for self-driving vehicles, traffic control, and security applications. This model has a 12-meter range. ...For more details visit...

This is a model of a 50 ohm Rosenberger Soldered Edge Launch 2.92mm connector (p/n : 02K249-40ML5) that is used for up to 40 GHz.There is a similar part from Bel Cinch Connectivity Solutions (Johnson) as p/n : 145-0701-811

... securely in place without having to tape them down. ... The antenna used in the photo is from a BetaFPV SuperD diversity transceiver– The clip is untested with other brands but it should work given they all have similar 2.4 Ghz antenna dimensions.