strike eagle throw lever 3d models

scope throw lever for a Swarovski Z5 rifle scope. ... 2mm cap screw and nut required.

A simple throw lever made to fit the Vector Optics Continental Series. ...Works with scopes with 30 as well as 34 mm tubes.

Throw lever for a burris 3x9x40. Takes a 3mmx10mm screw. Can probably be threaded into the plastic. ...I used a brass insert.

Resized this throw lever to fit my Athlon Talos BTR 4-14x44 rifle scope. ... Used M3x12 hex head bolt and nut to secure it.

A replacement throw lever for the element optics rifle scope. It's designed to slip over the zoom ring and has the lever offset by 17° to avoid interference from the bolt handle. ...The lever is hollowed out allowing the ring to flex and fit tightly...

This is a scope throw lever designed specifically for the Vortex Diamondback Tactical 6-24x scope. ...To ensure a secure fit, you might need to adjust it slightly to match your printer's dimensions around the magnification knob.

To eliminate the need for a screw, this throw lever has a lock key designed to be glued in after installation, making one solid piece. You may need to slightly file the ring to get the best fit of the key at the locking tabs. I recommend locking it...

I created this throw lever as a personal project and have loved it. ...I am uploading this so everyone else can enjoy it as much as I do.I have added in a drive lug to the inside ring to remove any ability for the lever to slip on the ring which also...

Throw Lever redesigned for the Sig Sauer Sierra 3 BDX 4.5-14x scope. I've tested it on alternative scopes, but unfortunately, I don't have access to the 3-9 or 6-20x models, so I'm unsure if it will fit perfectly. However, based on its design, it's...

I wanted a larger throw lever than what was available on my CVLIFE Scopes(https://a.co/d/29N7bz1). Let's the gun go into my cases. Uses M3 x 12mm Screw and nut. ... Added V2 which is thinner and more rounded for lower profile scopes.

Decided to Design my own throw lever rather than pay $30 and get one that only hopefully works. Uses an M2 nut which is inserted with the printer paused and a 12mm M2 hex socket cap screw. Can only guarantee it will fit on the specific model listed...

It makes zooming IN/OUT much easier (even in gloves) :)Uploaded model (both versions) has these parameters:inner diameter: 46,0 mmI use this throw lever on my rifle scope Vector Optics Matiz 3-9x/50mm but it can be used for any other.If you need to...

The F15E Strike Eagle is a US Air Force aircraft featuring pilots, adjustable weapon load and undercarriage. The 3D model, built to real-world scale (measured in meters), is designed using 3ds Max without requiring any additional plugins for...

Athlon Scope Throw Lever for the Argos 6-24x50 scope.

Throw lever to fit the Bushnell Elite 4500 scope. ... Print on it's side without any support.

This is a simple throw lever for the Monstrum G3 6-24 Scope. ... All you will need is m3 bolt and nut to install it.

This zoom throw lever fits perfectly on the Athlon Ares ETR 4.5-30x56 rifle scope, requiring minimal adjustments to ensure a precise fit. It is compatible with M3 thread inserts measuring 4 mm x 5 mm. ... Printed successfully from both PLA and ABS...

A throw lever designed for the Athlon Ares BTR Gen 1 scope. ...It should also fit the Ares ETR Gen 1 and the Midas Tac, although I have not tested that.Hardware required:1 M3x10 screw1 M3 nutCategory: Sport & Outdoors

Roue de réglage de parallaxe + levier de grossissement pour lunette vector optics continental (5-30x56). ...À monter en force. Parallax adjusment wheel + throw lever for vector optics continental scope (5-30x56). ...Interference fit.

Throw lever designed to fit Leupold VX-3 and VX-iiiL scopes, however it most likely fits other Leupold scopes as well (scopes with a ≈ 37.7 mm zoom ring and the gas inlet notch). At full magnification, the throw lever has good clearance for both the...

This is a throw lever for the Athlon Talos BTR 1-4X24 rifle scope. ...It slides over the magnification ring and uses an M4 Screw and bolt to tighten it onto the scope.

... SLX brakes I bought a set of Shimano Deore 6100 hydraulic brakes. ...Everything worked but I needed an allan key to adjust the throw on the lever. ...After a quick design on Onshape CAD software it was set to glue into the lever and start using it.

... smaller diameter. ...Regrettably, I don't have its precise measurements handy. Installing this item necessitates a 6-32 x 3/4 machine screw and nut. Alternatively, a larger throw lever for Vortex StrikeEagle 1-8x scopes is available in another upload.

This 3D printed throw lever is designed to perfectly fit a Vortex Diamondback 6-24x50 scope power ring. You will need a 3x10mm wood screw to tighten it. ...No support needed, just print it, put the screw, thighten it and you are good to go !

This is a throw lever designed for the Athlon Ares BTR Gen 1 scope. It should also fit the Ares ETR Gen 1 and the Midas Tac REVIII, although I have not tested that. ...   Requires 1 M3x10 screw and 1 M3 nut.

Re-mix from the throw lever by jitblass. I fixed the messed up geometry, beveled the edges (so you don't have to sand them afterwards), and shrunk the cutout for the nut to accept standard M3 nuts. Once printed, you'll need a M3 x 10 screw and...

I'm trying out the magnification throw lever that fits my Sig Tango 6 4-24x50 scope. I'm not sure if this will fit other SIG scopes in the tango line or their other models, so I'd appreciate feedback from anyone who tries it on different SIG scope...

This remix draws inspiration from miprotera's 'Bushnell 1x-4x Quick Adjustment Throw Lever', which can be found here: https://www.thingiverse.com/thing:2566788 The changes made include: Thickness is boosted by 0.3mm to enhance durability. Sides are...

Throw lever for Primary Arms 1-6x SFP scopes. This is an original design. **TABLE OF CONTENTS** - Parts - Printing Details **PARTS** - (1) M3x12mm socket head screw - (1) M3 nut **PRINTING DETAILS** - Settings (Tested on ender...

The Cat Tail Lever attachment is designed to complement the Optisan Mamba 1-4x scope, which had a limited release a couple of years back. ...This custom component was 3D printed without any support structures.