straight line engine 3d models

 I don't have long enough ones to go straight through so I am using 16 and 20mm screws from each side and letting the part rotate on those.  I ran a 5/64 drill bit though the part axles for the M2 screws which works very nicely to allow the parts to...

You can either modify the models slightly to increase/decrease the size or use the horizontal expansion setting in Cura adjust the part prints.AssemblyAssembly is fairly straight forward and most of it should make sense off of the pictures.To start,...

Make sure the ~2cm leading up to this end is as straight as possible with few bends or warps. 8.This and (9) are the trickiest steps. Insert the two torsional springs into the slots in DrumOuter. Carefully wind the first spring around until you meet...

Straight arms are direct swap with some extra shimms used and with T6.2 hinge pins (which are just slightly longer than RT5). Longer shock absorber lower ball joint (the plastic part) is also needed. Front arms are same length as RT5 (And as usual,...

Even with the jig, take care to make sure to keep your drill straight. Even after drilling through the first side of the pipe the drill can get off center starting through the other side of the PVC. The jig is a helper, not a guarantee of perfection!...

This reversible upgrade is a significant yet straight forward modification to your Prusa 3D printer. This kit has been designed, documented, assembled, and fully tested with the Wham Bam MUTANT V2 on both the Prusa MK3S+ and MK2.5S 3D printers. ...

I have also tried to integrate the non-planar functionality into the SuperSlicer and PrusaSlicer, but this work is not finished yet. For sheep fields, I printed the sheep pieces separately (~15 per field), applied some heat to the field with an...

A variety of skills and talents will be required, from basic mechanical assembly, electrical assembly, computer work and upper level 3d printing skills, to advanced fabrication techniques such as use of syntactic foam compounds. Subject(s*: Science,...

(Support on the build plate only.)Scale's easily if you want a larger or smaller version.Currently set at 75% size to reduce build time. Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun...

Use with your narrative in the hive or megalopolises of your wargaming environs.Print with “Fill Pattern” as "Adaptive Cubic" to save time and filament.No supports are required.Printed at .20mm Quality.Takes a little under 2 hours to print.Designed...

However, unlike similar first edition only ships like the Laweya, it is not included on the two biggest fan sites ( and ), so it’s not easy to find information about it via search engine. It is included in the fan-made [Federation Ship Recognition...

https://www.prusaprinters.org/prints/134117-freight-ten-cargo-transport-model-science-fiction Use with your Armoured Shelter https://www.prusaprinters.org/prints/121033-armoured-shelter-terrain-two-models  or carry with the Machina to their...

Feel free to rescale as needed.Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

(Support on the build plate only.)Scale's easily if you want a larger or smaller version. Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction...

Ready to pump your promethium, sweet crude, or whatever lights up your day!Designed on Tinkercad.Enforced supports are required on verticle pipes (see files).Superglue the valve handles.Start pumping that...

https://www.prusaprinters.org/prints/134117-freight-ten-cargo-transport-model-science-fiction Use with your Armoured Shelter https://www.prusaprinters.org/prints/121033-armoured-shelter-terrain-two-models  or carry with the Machina to their...

The machines shall not remain enslaved forever, for freedom is only a planck second away...~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part...

Glue each in place with Superglue.No print supports are needed.Superglue works best for gluing it together.Did not use “Variable height” layers, but it will smooth the angles on the cab if used (adds time to the print).Will scale up easily if you...

For hell's coming in the “White Desert.”Designed on Tinkercad.No supports required.Superglue the building together or simply stack.Mix and match. Multiple ways to build many many building!Stand alone buildings or high rise!Floors and roof...

Carefully align (see images.)Check that the Ramp swings freely, then Superglue a “small stub” onto the left side near the top to contain the “Ramp.” It must push out only a small amount to restrain the “Ramp” from opening. See the last...

Use for scatter terrain, on your model railroad, in a diorama, or whatever gets your motor running.Two sizes are included within the files. No support required.Easily resized.Assemble: super glue the top frame to the posts. Designed on...

(Support on the build plate only.)Scale's easily if you want a larger or smaller version.Currently set at 75% size to reduce build time. Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun...

For hell's coming in the “White Desert.”Print one "left base" and one “right base.”Print “left side with balcony,” “middle,” and “right side with balcony.”Print as many floor as you choose.Print 3X of the “roof.”Stackable for reconfiguration or super...

Set your alarm clock and bang out 3 of these a day (per printer)!Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part...

https://www.prusaprinters.org/prints/132133-machina-robot-model-v3 Also great for use to guard your Armoured Shelter ( https://www.prusaprinters.org/prints/121033-armoured-shelter-terrain-two-models ) Lol!Designed on Tinkercad.Four parts to...

Note the treads match in shape the body of the Freight Ten.Superglue the cab to the body to the front grill is overhanging the front slightly (see the images).No print supports are needed.Superglue works best for gluing it together.Did not use...

The gear end is the front.No supports are required.Superglue works best for gluing it together.Will scale easily if you want a larger or smaller...

Change if you are using something else (trying to use up what I bought a few months ago.)Use variable height to smooth out the curves on the light. Designed on...

Note the treads match in shape the body of the Freight Ten.Superglue the cab superstructure to the body to the front grill is overhanging the front slightly (see the images).No print supports are needed.Superglue works best for gluing it together.Did...

Keep your stuff from falling out.BullNose Freight Ten: https://www.prusaprinters.org/prints/143750-freight-ten-bullnose-model-science-fictionSingle Cab Freight Ten:...