stormcast eternals heads 3d models

Take apart the Gamesir controller with a small philips-head screwdriver on the back of the device. Then slightly peal back the rubber in the middle of the device to reveal more screws. You don't have to remove the rubber mat completely, just enough...

The menacing creature is depicted with its large crown-like carapace or the armoured head crest extending rearwards from their skull. The deadly representative of the strongest caste of Xenomorph has two sets of spike-like dorsal tubes and an extra...

Therefore, and also so to ensure the cleanest 3D printed result possible, each dorsal tube on each Xenomorph’s back, each creature’s head, tail and all extremities are provided as a separate assembly piece. If you take a look at the way the Queen...

The 3D artist did a perfect job portraying a humanoid aquatic creature with a head resembling one of a rooster, bulging eyes and fins. Monster’s mouth is full of tube-like appendages, its body is covered in scales and thin tentacles adore the...

Besides, Harry’s scarf was ‘taken off’ as well to ensure nice printing result and is attached to the figurine only by the boy’s head. All school trunks that are piled up behind the wizard come as separate files for you to choose yourself the way to...

Bullied by peers and disabled, Freddy is a very welcoming kid, he always keeps his head up and often even cracks jokes about his condition. So there is no way the author of the "Shazam and Freddy Freeman” diorama could have depicted the wizard’s...

Magneto's cape that is an integral part of the figurine was ‘taken off’ and split in half as well to ensure nice printing result and is attached to the figurine only by Magneto's head. All the assembly parts are provided in STL files in recommended...

and you always knew when the cistern was almost empty because the water would turn brown and the shower head would start to sputter. All in all, it took the better part of a day to fill that cistern with the pump outside Lyman's house at the bottom...

6.4mm / 3.2mm Heat Shrink Tubing (2:1 ratio)12voltplanet • Non-Insulated Male Blade Crimp Terminal Connectors2.8mm / 0.5 - 1.5mm² • 3.2mm / 1.6mm Heat Shrink Tubing (2:1 ratio)6.3mm / 0.5 - 1.5mm² • 6.4mm / 3.2mm Heat Shrink Tubing (2:1 ratio)6.3mm /...

The cook’s apron was ‘taken off’ to ensure nice printing result and is attached to the figurine by Bob’s head and held in place with the help of designated hole and trapezoid connector on the figurine’s chest. Such small elements as burger and plate...

The figurine’s head comes in two variants for you to choose from - with and without glasses. The glasses are also provided as a separate piece in the model’s assembly version though it is recommended to print them using DLP/SLA/SLS printers that are...

For you to achieve the cleanest 3D printed result, Treebeard’s leafy head, hands, feet, and numerous sprouts all over the creature’s body are provided as separate assembly pieces. All assembly parts are provided in STL files in recommended positions...

For you to achieve the cleanest 3D printed result, the Godfather’s head, hands and shoes were carefully separated, and even the rosebud was extracted from the left lapel of his jacket. All the assembly parts come in STL files in recommended positions...

Hulk’s arms, hands, head, and legs are provided as separate parts. All the assembly parts come in STL files in recommended positions that were worked out in order to ensure the smoothness of the details’ surfaces after printing and that the 3D...

For you to achieve the cleanest 3D printed result, Tifa’s gloved hands, left arm guard, boots, head, etc. are provided as separate assembly pieces. For the same purpose, Tifa’s long hair was cut off and divided into three separate parts, with the...

• 4 pcs AA battery, 1.5V • 2 pcs ballpoint pen spring • 2 pcs flat head metal push pin • 15 cm wire • lots of coin • super glue **Postscript** I have had the clock with the self climbing weight for about ten days. My ball chain was 3 meters long,...

The long horns from the kaiju’s head and his claws have also been separated. The model’s platform was divided into sixteen parts to fit the build plates of the average 3D printers. All assembly parts are provided in STL files in recommended positions...

Spider-Man’s arms, hands, head and legs are provided as separate parts. All the assembly parts come in STL files in recommended positions that were worked out in order to ensure the smoothness of the details’ surfaces after printing and so that the...

For you to achieve the cleanest 3D printed result, the figurine’s head and shoes were carefully extracted, while the model was also fully separated from its simple platform. All the assembly parts come in STL files in recommended positions that were...

For you to achieve the cleanest 3D printed result, the figurine’s head, shoes, hands, blow dryers, iron, gun, sling, plugs, etc. are provided as separate files. The cords do not come with STL files but can be made of a wire, a thin cable, a thick...

For you to achieve the cleanest 3D printed result, Aerith’s head, hands, boots, basket, flowers, etc. are provided as separate assembly pieces. For the same purpose, Aerith’s front bangs and long braid were cut off and divided into four separate...

* The “_hole.stl” versions of these have a single countersunk hole and hexahedron cut for a flat head M3 screw + hex nut located 6mm x 6mm from the closest corner. There are a couple uploaded pictures of example assemblies. A Comment On Strength...

For you to achieve the cleanest 3D printed result, the model’s head with hair, body, tail, arms, seashell, pearl, etc. are provided as separate assembly parts. All assembly parts come in STL files of FFF/FDM version in recommended positions that were...

A spot inside the Shadow Cat’s body (in FFF/FDM 1.0) allows to hide a battery inside the Mech’s head and introduce LED wiring to light up the cockpit. The CGauss and hand actuator that the Shadow Cat is equipped with are assembled in such a way that...

By then, the gladiator had already adorned his breastplate with symbols representing his many losses - there is a wolf's head, two-winged sphynx, Maximus’ wife and son, his horses, a tree and an angel. The gladiator holds a sword that Maximus wields...

In order for you to achieve the cleanest 3D printed result possible, the Knight’s head, Nail, both plants, the bench, as well as the model’s platform and lamppost were separated and come as independent assembly parts. All assembly parts come in STL...

For you to achieve the cleanest 3D printed result, the figurine’s head, dorsal tubes, spiky tail, feet, hands, etc. are provided as separate assembly parts. All assembly parts come in STL files of FFF/FDM version in recommended positions that were...

In order to conceal the places where the assembly parts of the model must be connected, the figurine was cut along the contour of A2’s outfit seams. For you to achieve the cleanest 3D printed result, the figurine’s hair...

Having reactivated the Engineer vessel, the Last Space Jockey heads for Earth to carry out his original mission to wipe out the human race. This scene from the 2012 Prometheus movie was the moment we’ve got to observe the incredible Engineer...

I looked at another even more scaled down remix and the STLs didn't look correct to me so I tried to make a 50% scaled down version myself.At 50% scale, it is about 33 mm wide and most holes are 2.25mm so it stands to reason that 1.75mm filament...