stock intel cooler 3d models

While the stock Ender 3 is a good starter printer and is for the most part very reliable and easy to use there is always room for improvement. I saw what a friend of mine had done with an Ender 3 Pro and I recently bought it off him and it inspired...

I saw no real reason to print the updated /  better one as this looked fine and worked well already.ClosetMaid Shelf I made this...

The stock motherboard enclosure and PSU WILL NOT FIT under the printer anymore with this mod in its default configuration and must be placed elsewhere. ...

( i used .6nozzle)1  : Pen Mount (support needed)1  : Top2 : GuidesThe mount is thin enough to not need longer screws, so you can use the ones holding the stock fan shroud. I used a small piece of double-sided adhesive tape between the...

No assembling required) Front cover:- Standard (No headlights, military type)- Alt version (with headlights for more expedition and civilian look) Steering wheel:- Standard (stock steering wheel look)- Alt version (custom 3 spoke steering wheel) Some...

It has built in cooling ducts for the extruders and mounts for the stock 30mm fans built in. I have included my new fan duct. Print one standard and one mirrored for this mount. The back is just the no sensor one from my other mount:...

It has built in cooling ducts for the extruders and mounts for the stock 30mm fans built in. I used Mistral 2.1A 4.5 from www.thingiverse.com/thing:2121279 as my cooling ducts. You need to mirror one for the other side but they fit and work great. ...

For that purpose, I've created a couple of different riser/feet options: This one uses the stock rubber pads: https://www.thingiverse.com/thing:5238215 This one uses the v-slots: https://www.thingiverse.com/thing:4937295...

The two screw holes that usually hold on the stock hotend should now have a few short rounded top M3 screws to hold this on. If your junk box lacks these, many cheap assortment boxes are out there. You also will need 4 M3x40 bolts for the receiver. ... ...

My problems with the part cooling duct in that design are (1) with the fan mounted on the side, it unevenly distributes air pressure to the two nozzles, (2) it's a relatively bulky fan duct, and (3) the mount for the stock 4010 fan was a poor fit. I...

 If you use this in a stock dome, you will need to figure out a solution for powering these LEDs yourself (you might be able to drive one from the original Radar Eye LED connection to the motherboard, but probably not both). PRINTING AND ASSEMBLY...

Here's a way to mount it onto your Ender 3 just like the stock display. Plus, as an added bonus, you can also mount a Biqu TFT35 display right alongside it. Please consider providing a Tip for the Designer since I'm on a very limited Social Security...

Book Collection: Stock your bookshelves with these beautifully detailed books and books on fantasy shelves. 4. Cozy Home Accents: Create inviting spaces with these intricately designed carpets in a range of colors, each featuring instance settings...

On my v2 it was the 28mm stock extruder mount. https://www.thingiverse.com/thing:4314829 # Print params # * Infill: 10%-15% * Support: NO * Raft: optional (really small one should suffice if you decide to go with one). * Layer: 0.2 *...

It has a simple mount: you just have to use the stock screws and screw them into the 4040.The right side (green piece in the photo) is a bit modular and adjustable. It uses the 2040 profile on the Ender 3, or the 4040 on the Ender 3 Pro, where the...

• Re-use the stock bolts for the x-axis cable mount. • Secure the wires to the mounts with zip ties. Parts ----- Below is my list of parts I used (affiliate links). • BIQU H2 v2.0:...

Feedback is welcome)Easy accessibility of the the lower screwV1 + V2About 30% less weight then the stock titan extruder with volcano hotendLess vibrations, higher speedGreat all Metal BIQU H2 DualGear extruderDrop-In Replacement for native Artillery...

A new Bull Run core repair kit is nearly $50 at this time including shipping and tax and can be hard to find in stock at times. However, this time around I have a 3D printer and so I built the one shown for about $1 in material and had it the...

Note: The project relies on "stock" LED mod already installed, mostly for holding cables in place and also integrates with the wiring for LEDs to save on space. It can be done stand-alone without LED strips as necessary. Note 2: I'm partial about...

... it will need filing to fit. The HERA stock top is attached using pieces of filament as pins. ...The optional pieces hold a couple 3mm led's if you want to light up the helix.If you want assembly Pictures… https://www.thingiverse.com/thing:5649157

All the models above were printed on 100% stock Ende 3 V1 (not even the Pro model). The stripes are done as three prints, printed one after another, without removing the previous prints from the bed. Print the part #1, then print #2 right over top of...

I made this mod primarily because I kept having binding issues with the stock rods. Overall I believe it to be a much better setup and it has fixed all the issues I was having with Z axis lines. This mod can be used entirely on it's own or in...

Your other options are PET tape or PEI sheets with an adhesive coating between the sheet and the steel shim.Steel shim link: https://www.mcmaster.com/steel-shim-stock/shim-stock-6/Instructions on sizing this are further down in the assembly...

Once woven they had numerous uses, the following offers some examples: as apron strings, binding at the waist edge of an apron and petticoats; garters used by men, women and children for their stockings; used as ties at the knees of men’s breeches,...

The default diameter of 16mm matches the size of the studs on the stock Prusa Original i3 MK2 spool holders and also the size of the cups on my modified MK2 spool holders so I kept that size here too so that I could re-use my existing rods. I print...

Franz Joseph II, Prince of Liechtenstein eventually showed interest in the manufacture of the device, and soon a newly formed company, Contina AG Mauren, began production in Liechtenstein.It was not long before Herzstark's financial backers, thinking...

This can be done by directly clamping both carriage parts together with the screws or using some spring loaded screws if you find some small springs (same concept as many CPU coolers). Hotend cooling is done with a simple 4010 axial fan and part...

It's up to you whether you print them all together or separately - the fan shroud needs support for the fan openings and the print cooler needs external support but preferably not internal support. The base itself will print as-is. I'd suggest a...

This was but the first step in a month-long effort which resulted in a complete redesign, there are no reused parts.The only two things that stayed the same are: the overall form (it is perfect as it is) and the location of the trigger axle (this...

USEFUL LINKS FOR PRINTER CALIBRATION AND TUNING: ------------------------------------------------------------------------------------ https://3dprintbeginner.com/artillery-sidewinder-x1-calibration-guide/...